2004 Dodge Ram 2500 4x4 High Out Put Cummins Low Miles on 2040-cars

Auto blog

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

Dodge Challenger spied exercising supercharged Hellcat Hemi V8

One of the prime complaints against the Dodge Challenger is that, even in SRT8 guise, its 470 horsepower is responsible for hauling over 4,200 pounds of vehicle. For comparison, the 420 hp in the Ford Mustang GT only has to deal with 3,618 lbs. Things only get worse from there, as the higher-performance variants of both the Mustang and the Chevrolet Camaro are far more powerful than an SRT8 without adding on much heft.
So what is Chrysler to do? The correct answer is add a whole lot more grunt to its hefty two-door and even the odds. That's where the all-new Hellcat engine comes into play. We reported on this engine in May, and suggested that the Hellcat, a supercharged powerplant based on a 6.4-liter V8, would easily generate 500 to 570 hp and could likely arrive boasting more than 600 ponies.
Chrysler's ace in its sleeve has now been spied testing, with a number of Hellcat-equipped Challengers running the potent new engine both in more urbanized areas and under the sun of Death Valley. The hoods on these testers have been raised to accommodate the engine, and that camouflage over the fascias of these prototypes is there to hide a larger air intake. We also note what appears to be a new split grille under wraps. As for power output, our spies are now suggesting a Viper-equalling 640 hp from the Hellcat-equipped cars.

Leno recalls '90s showdown with Tim Allen and his mullet

Not many of us have buddies with garages full of classic cars, but that isn't the case for Jay Leno and Tim Allen. Of course, one of the advantages for two guys with such vast collections is occasionally getting to pit their cars against each other. The two comedians did just that in the mid-'90s with a burnout battle on The Tonight Show between Allen in a race-prepped Mustang and Leno in a drag racer. After some time away from regular television, Leno is returning to the airwaves with a Jay Leno's Garage series premiering on Oct. 7 (tonight) at 10:00 p.m. ET on CNBC. Let this clip serve as another taste of what to expect for the new TV show's mix of comedy and cars. After reminiscing about the old days in a gorgeous garage, the comedians get into two modern machines to reprise the classic challenge – after a little trash talk anyway. Don't worry because the YouTube series isn't going anywhere, though.