1997 Dodge Ram 2500 Slt 12v Cummins Ext Cab Long Bed 2wd on 2040-cars

Auto blog

Common Dodge Ram 1500 vs. Chevrolet Silverado breakdowns

These two trucks are famous for their ability to get the job done. Still, even the toughest vehicle can have mechanical problems at some time. What if we match the Dodge Ram 1500 and Chevrolet Silverado head to head? Let's find out more about common repairs for each model. Also, learn some tricks to pay for car repairs. Clunky Steering Both Dodge and the Chevy owners sometimes notice bumping and clunking when steering. This might be more noticeable when driving over bumps. The cause is usually different in each truck though. In the Dodge Ram, clunky steering is more likely due to a defective lower ball joint. Replacement costs around $300 - $400, parts and labor. Clunky Chevy Silverado steering is probably a steering rack failure. This problem appears more often in trucks with over 90,000 miles. Silverado steering rack repair will run you up to $1,000 or more. Starting Woes For the Chevy Silverado with over 130,000 miles, you might notice trouble starting. This problem may appear occasionally at first, but it typically gets worse. Excluding a weak battery, the culprit is usually the starter. Replacement will cost you around $330 - $500. Of the total cost, $90 is for labor only. Now the Dodge Ram might make a ticking sound when starting, especially on models with over 94,500 miles. The noise often disappears after the engine warms up. These symptoms may indicate a broken exhaust manifold. Repair costs range from $800 - $900. Burning Oil & Gas Gauge On The Blink Sometimes, the Dodge Ram burns oil much faster than normal. In models with over 125,000 miles, this often points towards a leaky intake manifold gasket. A knocking sound may also appear with acceleration along with possible engine misfire. The cost to repair is around $200 - $300. The Chevy Silverado has its own surprises, especially when you've filled the gas tank but the gauge still reads low. Or the needle fluctuates widely from low to full while driving. In trucks with over 120,000 miles, it's likely due to a faulty fuel sensor. You might need a full fuel pump replacement, which can cost you up to $820, parts and labor. Water Inside And Poor Heat The Ram 1500 rear window has been known to leak. You might notice the back seat and floor wet after a rainstorm. This is more common in trucks with over 65,000 miles. Resealing the Ram 1500 rear window costs around $150 - $250.

Chrysler Group moves around execs in wake of recent departure

Chrysler is busy shuffling executives around in the wake of Ram head Fred Diaz's departure. The automaker has named Reid Bigland (pictured, right) as Diaz's successor in the role of president and CEO of Ram, though Bigland will continue his duties as the head of US sales and the president and CEO of Chrysler Canada. Bigland first came to Chrysler in 2006 from Freightliner Custom Chassis Corporation, so the guy knows a thing or two about trucks.
Meanwhile, Timothy Kuniskis will take over as president and CEO of Dodge. Previously, he served as the head of Fiat in North America and has been with Chrysler in one capacity or another since 1992. His old title now falls to Jason Stoicevich, who will also continue to work as the director of the automaker's California Business Center. Finally, Bruno Cattori will take over as the president and CEO of Chrysler Mexico.
Diaz left his position to take over as a divisional vice president of sales and marketing with Nissan. You can read the full press release on the Chrysler personnel changes below for more information.

Dodge Viper now available in matte finish

The prospect of buying a new Dodge Viper just got that much more enticing with the introduction of matte-finish paint direct from the factory. Available as part of the "1 of 1" customization program, the matte finishes aren't being offered in just a handful of colors like some other automakers do: customers will be able to specify a matte finish on any of the 8,000 colors that are already part of the program's palette. The matte finish option adds yet another step to the exhaustive hand-painting process that Dodge offers on the Viper - a painstaking endeavor that takes upwards of 145 man hours to complete. Specialists start by applying a base coat and a clear finish, followed by the paint and clear coat. The finished body panels are then smoothed with 1,000-grit paper and polished. A second sanding process is required for the matte finish before the application of a matte clear coat. Specify custom stripes (available in five colors or by custom order) and they're applied under the paint, not as decals on top. The availability of the matte finish in conjunction with the stripe options and new satin badging and fuel cap leads to over 50 million combinations. Needless to say, that means no two Vipers need ever leave the Conner Avenue assembly plant the same – though there will surely always be certain favorite combinations, especially on those units ordered from outside the customization program. Related Video: DODGE EXPANDS INDUSTRY-FIRST '1 OF 1' VIPER CUSTOMIZATION PROGRAM WITH NEW MATTE-FINISH PAINT OPTION - New matte-finish exterior paint available on all of Viper '1 of 1' program's 8,000 exterior color options and 24,000 stripe options - Viper's custom '1 of 1' exterior paint options double to 16,000 exterior colors and 48,000 unique strip combinations - Matte finish available in all exclusive '1 of 1' program and standard production colors - In addition to matte-finish exterior paint, Viper customers can choose between satin chrome or satin black badging and fuel filler door for a sinister appearance - Dodge Viper owners can build their one-of-a-kind Viper from more than 50 million unique build configurations for the ultimate in model year exclusivity June 19, 2015 , Auburn Hills, Mich. - The Dodge brand continues to expand the Viper's exclusive production elements like never before.