2008 Dodge Nitro Slt/rt on 2040-cars

Auto blog

Dodge engineers trying to shoehorn Pentastar into Dart?

The fact that the Dart's launch has been a pretty dismal affair isn't what we'd call secret. Judging by its mounting inventories and poor critical reception, Dodge's successor to its unloved Caliber has struggled since it hit the market. And while both of those are difficult problems to address, at least their cause is well known - the powertrain.
Even Fiat-Chrysler CEO Sergio Marchionne has acknowledged that the powertrain options in the Dart are substandard, admitting at January's Detroit Auto Show that the powertrains are "less than ideal." Leading with the 1.4-liter turbocharged four-cylinder found in the Fiat 500 Abarth left a bad taste in the mouths of consumers thanks to the laggy engine and dead throttle response (to say nothing of the manual and dual-clutch gearboxes that needed more refinement). The addition of the 184-horsepower 2.4-liter Tigershark in the Dart GT has helped matters some, but apparently Auburn Hills doesn't think it's quite enough.
If rumors are to be believed - get that salt ready - a possible solution may be in the works. A report from Allpar is claiming that Dodge is considering fitting a Pentastar V6 into the Dart's engine bay. As the Mopar-obsessed website points out, the critically acclaimed Pentastar is available in three different sizes - 3.0 liters, 3.2 liters and the original 3.6 liters. We don't get the 3.0 here in the US, but the 3.2 can be found in the new Jeep Cherokee and the 3.6 has been seemingly fitted to every model Chrysler can shoehorn it into.

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.

Dodge delaying Challenger Hellcats ordered with satin black hood [UPDATE]

The new Dodge Challenger SRT Hellcat is one of the most formidable muscle cars on the planet. And it looks the part, too – especially with the optional satin black hood. But if you were one of the first customers to place an order for the 707-horsepower Mopar muscle car and specified the black hood on the options sheet, you may have to wait awhile. According to members of the Hellcat.org forum cited by Car and Driver, deliveries of certain Challenger Hellcats have been delayed without explanation. When these fanatic customers started looking into the issue, they realized that all of the delayed orders shared one thing in common: they all had ordered their Dodges with that optional black hood. Although an exact reason wasn't specified, those who ordered the black hood on their Challenger coupes were told that delivery was being pushed back to February. But some were reportedly informed by their local dealership that things could be moved along if they switched their order to a body-colored hood instead. It's not clear if the issue is a supplier problem, a paint booth issue at the factory, or something else entirely. We've reached out to Dodge for clarification, and will update this story when we hear back. UPDATE: Reached for comment, a Dodge spokesperson confirmed to Autoblog that the satin black hood "is not currently available for production" and that customers who ordered it "can opt to change their order to a body-color hood" or otherwise have their orders delayed until the option becomes available at a later date to be confirmed.