2004 Dodge Neon on 2040-cars

Auto blog

NHTSA closes investigation on 4.7M FCA power modules, no recall

FCA US hasn't had the best time with recalls as of late. Not only did the company recently agree to greater safety oversight and paid $105 million to the government, that came just days after hacking fears prompted a 1.4-million model recall campaign. However, a recent decision to close an investigation by the National Highway Traffic Safety Administration means that the automaker doesn't have to worry about another major recall possibly affecting 4.7 million vehicles, according to the agency's report (as a PDF). Last September, the Center for Auto Safety petitioned NHTSA to investigate an alleged problem with the totally integrated power module (TIPM) on these FCA US models. The group claimed that a fault with the component could cause a variety of maladies, including stalls, not starting, catching fire, unintended acceleration, and airbag non-deployment. At the time, it also submitted 70 cases where this had reportedly happened. According to NHTSA, "no valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration, or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components." The agency did find signs of an issue with the fuel pump relay in some Jeep Grand Cherokees and Dodge Durangos, but FCA US issued recalls for the problem in September 2014 and February 2015. Without anything else to go on, the Feds don't think it's worth investigating this topic any more.

Dodge Journey and Fiat Freemont engine-cover recall affects 350k CUVs

FCA is recalling 349,731 examples of the 2011-2015 Dodge Journey and Fiat Freemont worldwide to better secure their engine covers. Of these affected vehicles, there are 144,416 in the US, 43,679 in Canada, 46,231 in Mexico, and 115,405 elsewhere. About 10 percent of them are also still at dealers, according to the automaker. Only models with the 2.4-liter four-cylinder engine are affected by this campaign. According to the company, the engine covers on these vehicles can be dislodged, and this can pose a fire risk if the loose part comes in contact with hot exhaust components. Warning signs of this happening include a noise under the hood, burning smell or a light on the instrument panel. The problem was discovered after three incidents on rough roads in Chile, and there was one minor injury there. According to FCA US spokesperson Eric Mayne to Autoblog, there have been eight occurrences of this issue reported in the US, but these were all related to "heat damage." There have been no reported injuries here. To fix the problem, dealers will install new engine-cover retainers on the affected models. These repairs will begin in August. As always for recall repairs, owners won't be charged. Statement: Engine Cover July 22, 2015 , Auburn Hills, Mich. - FCA US LLC is voluntarily recalling an estimated 144,416 crossover utility vehicles (CUVs) in the U.S. to better secure their engine covers. Engine covers in certain vehicles may become dislodged. If they come in contact with exhaust components, it may pose a fire risk. This condition was discovered during an FCA US investigation of three incidents in Chile. In each case, the vehicle had been driven extensively on unpaved or uneven surfaces. The Company is aware of a single related injury, described as minor. Affected are 2011-2015 Dodge Journey and Fiat Freemont CUVs equipped with 2.4-liter, four-cylinder engines. FCA US will install upgraded engine-cover retainers in these vehicles. The remedy will be available when customer notification begins next month; service will be performed free of charge. Vehicles equipped with six-cylinder engines are not affected. Additional Journey and Freemont populations also are subject to this campaign. They comprise an estimated 43,679 vehicles in Canada; 46,231 in Mexico; and 115,405 outside the NAFTA region. Of the 349,731 total vehicles subject to this campaign, approximately 10 percent remain in dealer hands.

Barracuda's Dodge branding no biggie, but what about engines?

Rumors about a revival of the Barracuda nameplate have been circulating for years now, though which brand it might fall under has been a bit of a mystery. Initial speculation had the car labeled an SRT product, but that acronym has since returned to its former role as a sub-brand for top-performance Mopars. Thanks to leaks from a recent FCA dealership event, we know the Barracuda is back on the table but will be sold under the Dodge umbrella, a move that has been generating a bit of ire from Pentastar fanatics, as the car was originally part of the defunct Plymouth brand. Given what's known about the new model, however, the badge is the least of my concerns about the new car. Let's start with the re-branding itself. This isn't the first time Chrysler has shuffled models around to different brands. The current-generation Viper spent two years as the flagship model under the SRT banner, only to return to Dodge for 2015 when SRT resumed its former role as a sub-brand. Years ago, the Neon was sold as a Plymouth, a Dodge, and a Chrysler model, depending on where you shopped for one. When Plymouth ceased to exist, the last few years of Prowler production got Chrysler badges instead. Then there's the new Jeep Renegade, a model whose name was born out of a trim level. The Barracuda might not turn out to be a muscle car in the way we currently define them. Further examples of naming liberties taken throughout automotive history could fill a book, but suffice it to say that these days a model's name has very little to do with the vehicle itself or any legacy it might have. The Barracuda name might be a particularly sacred cow with enthusiasts, but to me, a much bigger concern is the fact that the car might not turn out to be a muscle car in the way we currently define them. News from the Fiat Chrysler dealer briefing earlier this week indicates that when the next Charger debuts it will share its platform with the Barracuda, much the way the Charger and Challenger are twinned now. One difference is that the Barracuda is tipped to be offered as a convertible, while the modern Challenger is tintop-only. The Charger and Barracuda will use the rear-drive platform developed for Alfa Romeo's new Giulia, itself designed as a BMW M3 fighter both from a dimensional and dynamic standpoint; the Barracuda is expected to be slightly smaller than the current Challenger.