2007 Dodge Magnum Srt 8 on 2040-cars

Auto blog

Dodge Demon makes so much torque, it needs stronger driveline parts

Torque is a lovely thing, a sweet and wonderful force that twists and pulls and can help propel a two-ton metal box forward at comical speeds. Torque is also fickle and will bend and break those same metal parts without a second thought, which is why the new Dodge Demon is compensating for its increased torque with some new re-engineered and reinforced parts. And there's software intended to combat wheel hop, which one of the most dramatic ways torque can break stuff. Week 8's video, "Race-hardened Parts," gives a hint towards what all these new parts can do. While we still don't know how much torque the Demon will throw out, we do know it's enough to warrant an upgraded prop shaft, half shafts, and a differential housing. The Challenger Hellcat, which is the basis for the Demon, makes 650 pound-feet of torque already. The new parts will go a long way toward making sure the work from the Demon's engine is properly translated into motion by those Nitto drag radials. The new prop shaft uses high-strength steel, heat-treated stub-shafts, and increases the tube thickness by 20 percent for a 15 percent increase in torque capacity. Additionally, Dodge says the upgraded differential housing allows for a 30 percent increase in torque capacity by using heat-treated A383 aluminum alloy and a higher strength shot-peened gear set. The 41-spline half shafts that deliver 20 percent increased torque capacity through the use of high-strength low alloy steel and 8-ball joints. In addition to the hardware, the Launch Assist software has been tuned to help alleviate wheel hop. Dodge says the Demon is the first factory production car that uses wheel speed sensors to detect hop and momentarily cut torque to compensate. This means a driver can keep their foot planted on the floor while the computer sorts out the traction. Previously, the best solution was to back off the throttle to manually cut the load. Finally, the Dodge Demon will offer a four-point harness mounting bar as an optional accessory. The part will be supplied by Speedlogix and fits in place of the deleted rear seat. Customers can install the bar without having to hack apart their cars to find a proper mounting point. Look for more teasers and info on ifyouknowyouknow.com in the lead-up to the Demon's debut at the 2017 New York Auto Show. Related Video: Image Credit: FCA Dodge Performance dodge demon dodge hellcat

2015 Dodge Challenger SRT Hellcat has 707 glorious horsepower [w/video]

Hold onto your butts. "600-plus horsepower" is what we were told to expect from the 2015 Dodge Challenger SRT with its 6.2-liter supercharged Hellcat V8 engine. But as we've just learned, those were incredibly conservative numbers. Dodge has officially announced that the range-topping Challenger will hit the asphalt with 707 - seven hundred and seven - horsepower, making it the "most powerful muscle car ever."
Of course, 707 hp is only part of the story, as the Hellcat has also been confirmed to produce 650 pound-feet of torque. All that power will run exclusively to the rear wheels through an eight-speed automatic transmission that differs from other Challengers. The new gearbox, 8HP90 (rather than the 8HP70) is "upgraded to handle the extra power and torque," says Dan Reid, SRT's manager of product design and motorsports.
We certainly hope you're prepared to spend a ton of money replacing tires.

FCA recalling 63k Jeeps, Vipers and Ram ProMaster City vans

Fiat Chrysler Automobiles has announced a pair of recalls cover nearly 63,000 vehicles. The bigger of the two actions covers manual-transmission-equipped vehicles from 2006, including the Jeep Liberty and Wrangler, as well as the Dodge Viper. FCA engineers uncovered that the clutch ignition interlock switches use a kind of wire that was part of a previous recall campaign. Because of this, the company said that affected vehicles may not start, although in rare cases, "if recommended starting procedures are not followed," the affected vehicles may lurch forward after turning the key. Those recommended starting procedures "include activating the parking brake, placing the shift lever in neutral and pressing the clutch pedal before turning the vehicle's ignition key." Recall number two affects the company's 2015 Ram ProMaster City cargo and passenger vans. Owners will need to report to dealers to have a piece of tape removed from the side-curtain airbags. The tape is added during assembly and in some cases, may not have been removed. That could prevent the airbags from deploying in the event of a crash. Just under 59,000 vehicles are included in the first recall, including 43,874 in the United States, 11,309 outside of North America, 2,944 in Canada and 706 in Mexico. The ProMaster City recall includes just over 3,900 vehicles. FCA claims it's unaware of any injuries, fatalities or accidents related to either recall and will perform repairs free of charge. Scroll down for the official press release on both campaigns. Related Video: Statement: Clutch Ignition Interlock Switch April 23, 2015 , Auburn Hills, Mich. - FCA US LLC is launching a voluntary recall of an estimated 43,874 older-model U.S.-market cars and SUVs equipped with manual transmissions. The Company will replace their clutch ignition interlock switches at no charge to customers. The action follows an investigation by FCA US engineers that discovered these vehicles are equipped with switches that contain a certain type of wire implicated in a previous campaign. The wire, which was temporarily substituted by a supplier for the specified material, may break. As a result, the vehicles may not start, and in rare cases – if recommended starting procedures are not followed – a vehicle may exhibit unintended movement when its ignition key is turned. FCA US is unaware of aware of any related injuries or accidents involving this population of vehicles.