2009 Dodge Journey Sxt, Leather, One Owner on 2040-cars

Auto blog

Big rig gets blown over on Wyoming freeway, flattens police cruiser

A big rig navigating a stretch of windy Wyoming highway last week was blown over by high winds and landed on a Wyoming Highway Patrol cruiser. According to CBS News, three Wyoming Highway Patrol troopers responded to an accident along Interstate 80 near Elk Mountain on February 7. While the troopers were out of their cars assisting the crash victims, a white Volvo semi-truck lumbered up I-80 toward them. Wind gusts in that part of Wyoming were clocked in at up to 90 miles per hour on Tuesday, and one of them caught the semi as it neared the parked cruisers. Video from one of the cruiser's onboard cameras showed the big rig drift to the right as a big gust hit the trailer. Slowly, the whole rig tipped over and flattened one of the parked cruisers. The truck then slid a few feet on its side and came to a stop just aft of the cruiser. None of the troopers were injured in the incident, and two people in the truck came out of it unhurt as well. Patrol Lieutenant David Wagener told KGWN that that stretch of I-80 was closed on Tuesday to lightweight, high-profile vehicles. The truck driver was cited for the incident. High winds are no joke, and vehicles getting blown around or even clean off the road is a pretty common phenomenon. Way back in 2011, a truck got blown over in Utah. Then there was a train that got blown off a bridge in Louisiana in 2015. Related Video: News Source: CBS News, KGWN Auto News Dodge Volvo Driving Safety Truck Commercial Vehicles Police/Emergency Sedan semi truck rollover wyoming

Chrysler recalling 67k trucks with manual transmissions

Earlier this month, Chrysler announced the recall of some 280,000 pickup trucks over concerns that their axles could seize up. Now the automaker has announced an entirely separate recall of another 66,819 trucks over the springs that could break in the clutch ignition interlock switch. The recall affects Dodge Ram 1500, 2500 and 3500 pickups, as well as the Dodge Dakota and Mitsubishi Raider. The issue is relevant only to those trucks fitted with manual transmissions, from the 2006 and 2007 model years and manufactured between July 1, 2005, and July 31, 2006. Since a broken spring could, according to statements issued by the National Highway Traffic Safety Administration and FCA US LLC (previously known as the Chrysler Group) prevent the vehicle from starting, or cause it to move unintentionally once the ignition kicks over, the automaker will begin notifying owners of the affected vehicles just before Valentine's Day to bring their trucks into their local dealers to have the clutch ignition interlock switch replaced. FCA emphasizes, however, that the unintended movement would only occur "in rare cases" and only "if recommended starting procedures are not followed." Only one such case is known to have occurred, but it did regrettably result in a fatality. Statement: Clutch Ignition Interlock Switch December 29, 2014 , Auburn Hills, Mich. - FCA US LLC is launching a voluntary global recall of an estimated 66,819 older-model pickup trucks equipped with manual transmissions. The Company will replace their clutch ignition interlock switches at no charge to customers. An investigation by FCA US engineers discovered switches in certain model-year 2006 and 2007 pickups may be equipped with spring wire that differs from wire used in previous switches. The alternate wire may break and, as a result, the vehicles may not start. In rare cases, a vehicle may – if recommended starting procedures are not followed – exhibit unintended movement when its ignition key is turned. The Company is aware of one fatality related to this campaign. It stemmed from the single known accident involving this population of vehicles. The recall covers certain Dodge Dakota, Dodge Ram 1500, 2500, 3500 and Mitsubishi Raider pickups. Switches with the alternate wire were not used in any vehicles produced before July of 2005, or after June of 2006. The Dakota and Raider are no longer in production.

Chrysler almost smothered the Hellcat before it lived

Chrysler's 6.2-liter supercharged Hellcat V8 was an absolute sensation from the very moment it was announced, and honestly, how could it not have been? Packing 707 horsepower and 650 pound-feet of torque, its numbers immediately put every other production muscle car (and many supercars) to shame. Plus, we soon learned that would be wrapped in a package retailing for around $60,000 - a pittance compared to other vehicles offering similar grunt. However, the Hellcat almost never got the chance to rumble under the hood of the Challenger and Charger.
The Hellcat was initially proposed back in 2011, back when Fiat was deciding its future strategy for Chrysler Group, according to Automotive News. At the time, the company was just emerging from its bankruptcy doldrums, and an ultra-high-performance V8 wasn't exactly a must-have item. The program didn't move forward. However, SRT engineers kept fighting, according to AN, and four months later, they received the green light to pull the project off the shelf and continue developing the Hellcat. The muscle car world is certainly better for that decision.
The work of those engineers focused on taking Chrysler's standard 6.2-liter V8 and making it reliably handle all of the extra power from the supercharger. "It came down to micron levels of changes in the crank to be able to withstand the pressures of the engine," said Chris Cowland, director of advanced and SRT powertrain, to Automotive News. The changes amounted to switching out about 91 percent of the parts to make the Hellcat, including some quite minuscule alterations. For example, the washer holding the supercharger pulley is embedded with industrial diamonds to keep it from slipping.