2.7l Power Steering Power Door Locks Power Windows Tachometer Cruise Control on 2040-cars

Auto blog

Indications of 825 hp and emissions issues for Hellcat called 'speculation' by Chrysler

The 2015 Dodge Challenger SRT Hellcat is probably one of the hottest cars of the moment mostly because of its insane, 707-horsepower supercharged V8. However, there are conflicting reports coming out that the powerplant might be having problems with its emissions compliance and may be capable of even more power.
Jalopnik says that an unnamed source within Fiat Chrysler Automobiles told it that the Hellcat was having problems meeting emissions standards at its 707-horsepower tune. The person claimed that the automaker has been testing the V8 with different types of sensors, possibly to make it a bit cleaner in the future. Autoblog spoke to SRT spokesperson Dan Reid, and he said about the claimed poor emissions, "It's totally speculation."
The source also claimed that the Hellcat had been dynoed at a monumental 825 horsepower, internally. Based on the other rumor, though, it's hard to imagine the engine being emissions compliant like that. Autoblog also asked Reid about this speculation about more power and was told, "They are totally speculating about that."

Dodge idles Viper production again at Conner Avenue

You've got to hand it to Dodge for having the gumption to put the original Viper into production in the first place. It was, after all, much more of an emotional decision than a practical one, and a move which saw the first production V10 engine placed in a road car - long before the advent of the Lamborghini Gallardo, Audi R8, Porsche Carrera GT or Lexus LFA, not to mention the other Ford, BMW and Volkswagen Group models that used such engines.
It's now been 22 years since the first Viper entered production and the Viper still rolls on several generations later, but we're sad to say that courageous decision has not always been met with overwhelming sales success. In fact parent Chrysler was forced to idle the Conner Avenue plant where the Viper is made back in April due to slow sales. And while production resumed again as planned on June 23, it apparently didn't do the trick.
As a result, Chrysler corporate communications chief Shawn Morgan revealed to Autoblog that the assembly line has been shut down again for another two weeks. The line was up and running for nearly two full work weeks from June 23 until the holiday weekend that started on Thursday, July 3. But instead of coming back online today as planned, it's been idled again for the weeks of July 7 and 14. That means it will be July 21, at the earliest, before the serpentine supercars start slithering down the assembly line at Conner Avenue again. Once it does, however, production is set to resume at the same pace it was before the shutdown.

Chrysler says its 8-speed transmissions will save 700 million gallons

Chrysler Group's TorqueFlite eight-speed transmission could be earning some serious green bragging rights if the company's projections are correct. The recently widely proliferated automatic gearbox, which is now in more than a million vehicles around the world, is poised to save drivers an estimated 700+ million gallons of fuel over the vehicles' lifetimes (an expected cost savings of $2.5 billion). In addition, Chrysler expects a reduction in CO2 emissions by more than six million metric tons. According to Chrysler, and depending on the vehicle, the TorqueFlite can improve fuel economy. The TorqueFlite autobox features particularly close ratios from fifth to eighth gear (see the press release below for the specific numbers), and uses low-viscosity fluid that doesn't need to be replaced. Transmission software adapts to the driving situation to optimize efficiency based on driver behavior, temperature, grade, stability control, and longitudinal and lateral acceleration. The TorqueFlite is capable of handling a variety of duties. As evidenced by the wide range of vehicles Chrysler Group has seen fit to equip with the eight-speed transmission, the TorqueFlite is capable of handling a variety of duties. Since its 2012 introduction, the TorqueFlite has gone from performing cog-swapping duties in Dodge Charger and Chrysler 300 models equipped with the 3.6-liter Pentastar V6 to changing gears in vehicles such as the Pentastar- and Hemi-powered Dodge Durango, Jeep Grand Cherokee and even the Ram 1500 EcoDiesel. For the 2015 model year, the eight-speed is finding its way into even more vehicles with the addition of a third version. In addition to the American-made TorqueFlite 845RE and 8HP70, the new 8HP90 will be manufactured in Saarbrucken, Germany. The 8HP90 is designed for higher torque loads, making it ideal for high-performance vehicles like the 2015 Dodge Challenger SRT Hellcat. The already-in-use 8HP70 will expand its duties to be used in 2015 Hemi models such as the Dodge Charger, Challenger, and Challenger SRT8. You can see the list of those benchmarks in Chrysler's press release below.