2014 Dodge Dart Gt on 2040-cars

Auto blog

Big rig gets blown over on Wyoming freeway, flattens police cruiser

A big rig navigating a stretch of windy Wyoming highway last week was blown over by high winds and landed on a Wyoming Highway Patrol cruiser. According to CBS News, three Wyoming Highway Patrol troopers responded to an accident along Interstate 80 near Elk Mountain on February 7. While the troopers were out of their cars assisting the crash victims, a white Volvo semi-truck lumbered up I-80 toward them. Wind gusts in that part of Wyoming were clocked in at up to 90 miles per hour on Tuesday, and one of them caught the semi as it neared the parked cruisers. Video from one of the cruiser's onboard cameras showed the big rig drift to the right as a big gust hit the trailer. Slowly, the whole rig tipped over and flattened one of the parked cruisers. The truck then slid a few feet on its side and came to a stop just aft of the cruiser. None of the troopers were injured in the incident, and two people in the truck came out of it unhurt as well. Patrol Lieutenant David Wagener told KGWN that that stretch of I-80 was closed on Tuesday to lightweight, high-profile vehicles. The truck driver was cited for the incident. High winds are no joke, and vehicles getting blown around or even clean off the road is a pretty common phenomenon. Way back in 2011, a truck got blown over in Utah. Then there was a train that got blown off a bridge in Louisiana in 2015. Related Video: News Source: CBS News, KGWN Auto News Dodge Volvo Driving Safety Truck Commercial Vehicles Police/Emergency Sedan semi truck rollover wyoming

Dodge recalls 27k Darts for bracket that can disrupt transmission module

Dodge is recalling 27,520 examples of the 2013-2015 Dart with dual-clutch gearboxes. The mounting bracket for the transmission control module can affect the part's operation and cause the compacts to suddenly shift into neutral. According to the automaker, 23,688 of them are in the US, 3,376 in Canada, 5 in Mexico, and 451 elsewhere. The National Highway Traffic Safety Administration reports these examples carry build dates between February 24, 2012, and June 16, 2015. There are also no reports of accidents or injuries. Because of the way the bracket is mounted, the part can put too much force on the control module's circuit board and cause it to shift out of gear. The engine and airbags remain operable if this happens. To fix things, dealers will install a redesigned mount and replacement module. Related Video: Statement: Mounting Bracket September 14, 2015 , Auburn Hills, Mich. - FCA US LLC is recalling an estimated 23,688 cars in the U.S. to replace certain control modules and mounting brackets that may contribute to a loss of motive power. The Company is unaware of any related injuries or accidents. An FCA US investigation prompted by a small number of warranty claims discovered a control-module mounting bracket may apply too much force and disrupt the function of a circuit board within the module. This condition, unique to certain cars equipped with dual dry-clutch transmissions (DDCT), may cause the transmission to shift into neutral. However, the engine remains on and the vehicle's air-bags, as well as other safety features, are unaffected. The condition may also be preceded by the illumination of a dashboard warning light. Customers who observe this are urged to contact their dealers. The campaign is limited to certain 2013-2015 Dodge Darts equipped with DDCTs. Additional vehicles will be recalled in Canada (3,376), Mexico (five) and outside the NAFTA region (451). Affected customers will be advised when they may schedule service, which will be performed free of charge. Service will entail installation of a redesigned mounting bracket and replacement of the control module. Customers with additional questions may call the FCA US Customer Information Center at 1-800-853-1403.

2025 SRT Hellcat concepts as previewed by high schoolers

Fiat Chrysler Automobiles has some very talented designers in its ranks. Like any good company, though, the automaker is always on the lookout for early talent. Even if they're still in high school. One of those talent-seeking initiatives is the company's Drive for Design contest, an event open to tenth-, eleventh-, and twelfth-grade students that are hoping for a future in design. For this year's event, students from across the country were given a shot to design their vision for a 2025 model-year Dodge SRT Hellcat. The results are impressive, as you can see in the gallery above. First place went to Ben Treinen, from Archbishop Moeller High School in Cincinnati. Second place was the only award to go to a student outside the Rust Belt, with Macon, GA's Harrison Kunselman, a student at Mount de Sales Academy taking the silver. Third place was won by a metro Detroiter – Bloomfield Hills High School student Hwanseong Jang, while fourth went to Andrew Gombac of Loyola Academy in Wilmette, IL. According to FCA, all four winners will have their sketches on display at the 2016 Autorama at Cobo Center at the end of February. They'll also win some pretty nifty prizes. First place will get a new Apple MacBook Pro, while second, third, and fourth get the new Apple iPad Pro and Apple Pencil (arguably just as good of a prize for budding designers). All four finishers will also attend a three-week automotive design course at Detroit's prestigious College for Creative Studies, have dinner with FCA designers, and score three passes to Autorama. FCA will cover travel and lodging to Auburn Hills. Read on for the official blast from FCA. Related Video: FCA US Design Team Announces Winners of Drive for Design Contest January 19, 2016 , Auburn Hills, Mich. - The FCA US LLC Design team today announced four winners in this year's Drive for Design contest. The FCA US Drive for Design contest challenged U.S. high school students in grades 10-12 to design a Dodge SRT Hellcat for the year 2025. "The Drive for Design contest continues to be a great way for the FCA US Design team to connect with students that show an interest in art and design," said Mark Trostle – Head of Dodge and SRT Design, FCA US LLC.