1967 Dodge Coronet R/t 4 Speed Look!! on 2040-cars

Auto blog

Say goodbye to the Dodge Dart and Chrysler 200

Fiat-Chrysler CEO Sergio Marchionne outlined an update to the company's five-year business plan Wednesday, and among the changes, the Dodge Dart and Chrysler 200 sedans will soon be phased out. The company's presentation to investors states that the "market shift from cars to trucks and UVs [utility vehicles is] now seen as permanent shift in demand," and FCA wants to respond as quickly as possible. Killing the 200 and Dart will allow FCA to build more Jeep and Ram models at the Sterling Heights, MI, and Belvidere, IL, plants where the sedans were produced. We already knew FCA was planning to shift 200 and Dart production to Mexico, to free up the Sterling Heights facility for Ram 1500 production, and the Belivdere site for Jeep Cherokee output. The Cherokee will move from its current home in Toledo, OH, to allow for increased Wrangler production. It's no shock that FCA wants to shift its focus to crossovers and trucks. In December 2015, for example, combined sales of the Dodge Dart and Chrysler 200 were 15,310. The Jeep Cherokee, which uses the same platform as the Dart and 200, outsold both models combined, with 24,049 sales. Both the Dart and 200 had troubles from the beginning. Marchionne recently blamed designers for the 200 not receiving a Consumer Reports 'recommended' rating, and the Dart was one of the lowest-scoring cars in a CR reliability study. Featured Gallery 2013 Dodge Dart: Review View 27 Photos Related Gallery 2015 Chrysler 200 View 43 Photos Image Credit: Copyright 2016 Drew Phillips / AOL Chrysler Dodge Jeep RAM FCA confirmed

Chrysler recalls small number of 2013-2014 cars and trucks over engine debris

Chrysler is recalling a small number cars over issues with their 2.4-liter four-cylinder engines. The recall, which affects 522 examples of its 2013 Dodge Avenger and Chrysler 200 models, as well as 2014 Jeep Compass and Patriot CUVs has to do with potential debris in the balance shaft bearings.
The abrasive stuff can cause the oil pressure to drop, which could lead to the engine stalling or outright failure. This situation could at best leave drivers stranded and at worst lead to a crash.
Chrysler will begin notifying owners, who will need to report in to have the balance shaft module replaced. All repairs are naturally free of charge. Scroll down for the bulletin from NHTSA.

Chrysler says its 8-speed transmissions will save 700 million gallons

Chrysler Group's TorqueFlite eight-speed transmission could be earning some serious green bragging rights if the company's projections are correct. The recently widely proliferated automatic gearbox, which is now in more than a million vehicles around the world, is poised to save drivers an estimated 700+ million gallons of fuel over the vehicles' lifetimes (an expected cost savings of $2.5 billion). In addition, Chrysler expects a reduction in CO2 emissions by more than six million metric tons. According to Chrysler, and depending on the vehicle, the TorqueFlite can improve fuel economy. The TorqueFlite autobox features particularly close ratios from fifth to eighth gear (see the press release below for the specific numbers), and uses low-viscosity fluid that doesn't need to be replaced. Transmission software adapts to the driving situation to optimize efficiency based on driver behavior, temperature, grade, stability control, and longitudinal and lateral acceleration. The TorqueFlite is capable of handling a variety of duties. As evidenced by the wide range of vehicles Chrysler Group has seen fit to equip with the eight-speed transmission, the TorqueFlite is capable of handling a variety of duties. Since its 2012 introduction, the TorqueFlite has gone from performing cog-swapping duties in Dodge Charger and Chrysler 300 models equipped with the 3.6-liter Pentastar V6 to changing gears in vehicles such as the Pentastar- and Hemi-powered Dodge Durango, Jeep Grand Cherokee and even the Ram 1500 EcoDiesel. For the 2015 model year, the eight-speed is finding its way into even more vehicles with the addition of a third version. In addition to the American-made TorqueFlite 845RE and 8HP70, the new 8HP90 will be manufactured in Saarbrucken, Germany. The 8HP90 is designed for higher torque loads, making it ideal for high-performance vehicles like the 2015 Dodge Challenger SRT Hellcat. The already-in-use 8HP70 will expand its duties to be used in 2015 Hemi models such as the Dodge Charger, Challenger, and Challenger SRT8. You can see the list of those benchmarks in Chrysler's press release below.