1966 Dodge Coronet 500 With Built 440 Auto Ps Pb on 2040-cars

Auto blog

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.

Common Dodge Ram 1500 vs. Chevrolet Silverado breakdowns

These two trucks are famous for their ability to get the job done. Still, even the toughest vehicle can have mechanical problems at some time. What if we match the Dodge Ram 1500 and Chevrolet Silverado head to head? Let's find out more about common repairs for each model. Also, learn some tricks to pay for car repairs. Clunky Steering Both Dodge and the Chevy owners sometimes notice bumping and clunking when steering. This might be more noticeable when driving over bumps. The cause is usually different in each truck though. In the Dodge Ram, clunky steering is more likely due to a defective lower ball joint. Replacement costs around $300 - $400, parts and labor. Clunky Chevy Silverado steering is probably a steering rack failure. This problem appears more often in trucks with over 90,000 miles. Silverado steering rack repair will run you up to $1,000 or more. Starting Woes For the Chevy Silverado with over 130,000 miles, you might notice trouble starting. This problem may appear occasionally at first, but it typically gets worse. Excluding a weak battery, the culprit is usually the starter. Replacement will cost you around $330 - $500. Of the total cost, $90 is for labor only. Now the Dodge Ram might make a ticking sound when starting, especially on models with over 94,500 miles. The noise often disappears after the engine warms up. These symptoms may indicate a broken exhaust manifold. Repair costs range from $800 - $900. Burning Oil & Gas Gauge On The Blink Sometimes, the Dodge Ram burns oil much faster than normal. In models with over 125,000 miles, this often points towards a leaky intake manifold gasket. A knocking sound may also appear with acceleration along with possible engine misfire. The cost to repair is around $200 - $300. The Chevy Silverado has its own surprises, especially when you've filled the gas tank but the gauge still reads low. Or the needle fluctuates widely from low to full while driving. In trucks with over 120,000 miles, it's likely due to a faulty fuel sensor. You might need a full fuel pump replacement, which can cost you up to $820, parts and labor. Water Inside And Poor Heat The Ram 1500 rear window has been known to leak. You might notice the back seat and floor wet after a rainstorm. This is more common in trucks with over 65,000 miles. Resealing the Ram 1500 rear window costs around $150 - $250.

Chrysler almost smothered the Hellcat before it lived

Chrysler's 6.2-liter supercharged Hellcat V8 was an absolute sensation from the very moment it was announced, and honestly, how could it not have been? Packing 707 horsepower and 650 pound-feet of torque, its numbers immediately put every other production muscle car (and many supercars) to shame. Plus, we soon learned that would be wrapped in a package retailing for around $60,000 - a pittance compared to other vehicles offering similar grunt. However, the Hellcat almost never got the chance to rumble under the hood of the Challenger and Charger.
The Hellcat was initially proposed back in 2011, back when Fiat was deciding its future strategy for Chrysler Group, according to Automotive News. At the time, the company was just emerging from its bankruptcy doldrums, and an ultra-high-performance V8 wasn't exactly a must-have item. The program didn't move forward. However, SRT engineers kept fighting, according to AN, and four months later, they received the green light to pull the project off the shelf and continue developing the Hellcat. The muscle car world is certainly better for that decision.
The work of those engineers focused on taking Chrysler's standard 6.2-liter V8 and making it reliably handle all of the extra power from the supercharger. "It came down to micron levels of changes in the crank to be able to withstand the pressures of the engine," said Chris Cowland, director of advanced and SRT powertrain, to Automotive News. The changes amounted to switching out about 91 percent of the parts to make the Hellcat, including some quite minuscule alterations. For example, the washer holding the supercharger pulley is embedded with industrial diamonds to keep it from slipping.