2006 Dodge Charger Base Sedan 4-door 2.7l on 2040-cars

Auto blog

2018 Dodge Challenger SRT Demon First Drive | Don’t fear the Demon

"If you're not hurt, we'll be really pissed. If you are hurt, we'll still be pissed, but not quite as pissed." These are the words from Jim Wilder, the vehicle development manager of the 2018 Dodge Challenger SRT Demon, that echo through our head as we slide behind the wheel of the car for the first time. He was warning us about driving beyond our abilities, and keeping the car out of the wall. With 840 horsepower and 770 pound-feet of torque on tap from its supercharged, 6.7-liter V8, the Demon does 0-60 miles per hour in 2.3 seconds, and 0-30 mph in a second flat. If something does go wrong, it'll happen quickly. Following that talk, we had our guts sloshed as a passenger in a blurry eighth-mile run, giving us a taste of the G forces (the Demon can pull 1.8 G in a straight line) we'd feel when we got in the driver's seat for our own pass down the drag strip. We're already sweating. It had rained - you could describe it as torrential - the day before. The grassy parking areas surrounding Lucas Oil Raceway were still flooded, but any water on the pavement had evaporated and hung in the air. Combined with the heat, we were sticky and uncomfortable. In Drag Mode, the Dodge Demon's air conditioning turns off. Any condensation that it could leave on the track would be a problem, plus we need to reduce parasitic power losses for a faster run. The system is still working, though, the refrigerant diverted to the chiller system cooling the air coming into the engine. There's still condensation, but the Demon collects it on a catch pad to keep it from ending up on the pavement. We're also required to roll the windows up when entering the drag strip. For one thing, it helps keep the smoke out of the cabin during the pre-staging burnout. So, yeah, it's hot as Hell in the Demon. We pull through the water box and run through the sequence – which involves holding the "OK" button on the steering wheel usually used to navigate menus, and applying a specific amount of brake pressure before getting on the throttle to initiate the burnout. This gets any crud off the rear tires and heats up the rubber. There are multiple ways to launch the Demon. We had an instructor sitting in the passenger seat as we pulled up to the beams that trigger the Christmas tree at Lucas Oil Raceway. He walks us through the most complicated of the three he had explained to us just minutes before when we were in the passenger seat.

500+ hp Stellantis 'Hurricane' I6 previews a world without Hemis

After years of rumored development, Stellantis has revealed its new six-cylinder engine family. The 3.0-liter, twin-turbocharged "Hurricane" I6 will offer V8 power, forced induction torque and six-cylinder efficiency in a package designed to fit into any of the company's North American rear-wheel-drive platforms.  What is "V8 power," exactly? Well, in standard output guise, the new I6 cranks out more than 400 horsepower (the specific figure will vary by application) and 450 pound-feet of torque, while the high-output variant is good for more than 500 horses and 475 lb-ft. The final figures will be dependent on the application. We'll save you a little legwork: In current Ram, Jeep and Dodge products, the 5.7-liter Hemi tops out at about 395 hp and 410 lb-ft, give or take, and the 6.4-liter around 485 hp and 475 lb-ft.    This is a clean-sheet design that is only related to the company's turbocharged four-cylinder by some common measurements. The I6 is exclusively direct-injection (no hybrid/port-injection here) and the two I6 variants share 96 common parts, including the block and oil pan design. The differences are found in their internals, intake plumbing, valvetrain components and the turbochargers themselves. Stellantis is not yet ready to share specs or supplier info for the turbos but says announcements will come from its partners soon.  The standard-output I6 has a compression ratio of 10.4:1 and revs to 5,800 rpm. It will run on regular fuel, albeit with reduced performance; 91 octane is recommended for maximum output. The high-output variant has a compression ratio of 9.4:1 and will rev to 6,100 rpm. That one will require premium. The new I6's advantages go beyond basic power output. Every Hemi family engine currently in production is based on an iron block design, so they're heavy. The aluminum-block I6 shaves weight off the total engine package, even if some of that gets added back thanks to the turbos and their associated plumbing. The standard-output I6 weighs 430 pounds, Stellantis engineers told us; the high-output adds just another 11. Fully dressed 5.7-liter V8s are in the 550-560-pound ballpark, and 6.4-liters close in on 600 pounds.  You may be wondering, "Why a clean-sheet gasoline engine now, when the industry is moving toward battery-electrics?" A valid inquiry, and one Stellantis was prepared to address. While the company will be pivoting to electrification over the next decade, it won't be instantaneous.

Chrysler patents smarter minivan folding seats

It's frightening to think of how quickly the mice would have overtaken us if we hadn't stayed one step ahead of them with better mousetraps. We'll never have to worry about that in our relentlessly re-engineered world, though. Case in point: Chrysler has been granted a patent by the US Patent and Trademark Office for an improved design of the already wondrous Stow 'n' Go seating found in the automaker's Town and Country and Dodge Grand Caravan minivans.
Introduced in 2005, the Stow 'n' Go was improved in 2008, and based on the drawings of this third-generation improvement, the new design appears to allow stowage of the second row of seats without having to move the front-row seats forward as much. It look like it also involves fewer operations and moving parts, with a portion of the seatback being incorporated into the flat floor when the seats are stowed, as opposed to having a completely separate cover.
It's possible that the innovation may appear on the next-generation minivans expected in 2015, but Chrysler isn't commenting on the patent.