2023 Dodge Challenger R/t Scat Pack on 2040-cars

Auto blog

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.

NHTSA closes investigation on 4.7M FCA power modules, no recall

FCA US hasn't had the best time with recalls as of late. Not only did the company recently agree to greater safety oversight and paid $105 million to the government, that came just days after hacking fears prompted a 1.4-million model recall campaign. However, a recent decision to close an investigation by the National Highway Traffic Safety Administration means that the automaker doesn't have to worry about another major recall possibly affecting 4.7 million vehicles, according to the agency's report (as a PDF). Last September, the Center for Auto Safety petitioned NHTSA to investigate an alleged problem with the totally integrated power module (TIPM) on these FCA US models. The group claimed that a fault with the component could cause a variety of maladies, including stalls, not starting, catching fire, unintended acceleration, and airbag non-deployment. At the time, it also submitted 70 cases where this had reportedly happened. According to NHTSA, "no valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration, or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components." The agency did find signs of an issue with the fuel pump relay in some Jeep Grand Cherokees and Dodge Durangos, but FCA US issued recalls for the problem in September 2014 and February 2015. Without anything else to go on, the Feds don't think it's worth investigating this topic any more.

2015 Dodge Viper GTC available in 25 million no-cost combos with 1 Of 1 bespoke program

What's the one thing no car can have too much of? Here's a hint – it's not power. It's not efficiency, either, or technology, or even safety. It's exclusivity. It's one reason Rolls-Royce has become a legend building absolutely bespoke motor vehicles, and it's the reason Dodge, of all companies, is offering a new GTC trim level for its Viper supercar. Now, you might be asking what's so special and exclusive about a trim level? Well, in the Viper GTC's case, it gives owners access to a catalog of 8,000 shades of paint for the exterior, 24,000 "hand-painted" custom stripe patterns, 10 different wheel options, 16 interior trims and no fewer than six aerodynamic packages. That results in 25 million different configurations for the 645-horsepower snake. Most shockingly, the customization choices come at no additional cost on the GTC model. And it's only the start. Ordering a GTC will enroll customers in a unique VIP program called Viper Concierge, which according to Dodge, "offers an exclusive point of contact throughout the custom Viper build process." In other words, buyers will be given the means to stay right on top of their car's production, through the 140-to-160-hour painting process, which itself will be fully documented with pictures and through a mobile-friendly website, to the actual construction of their GTC. The Concierge process will start with the ordering stage, which will include Dodge sending customers a paint chip showing the owner's custom choosing, which they can confirm or refuse. Shortly thereafter, Dodge will send buyers a 1:18-scale "speed-form" replica in their chosen custom colors, once again to confirm or deny the build. Once the buyer's color and option selection is locked-in, that car becomes a one-of-one Viper for that year – no other buyer will be permitted to build a Viper to the same specifications. The concierge service also grants access to the Viper Ambassador Owner's Portal, where orderers can track their car's build process, receive weekly updates and share their excitement with (jealous) friends and family. And once the car is complete, it will be fitted with a custom dash plaque identifying its bespoke provenance – the owner can choose to have their name put on the badge, the car's nickname, or whatever they wish (Dodge will also ship each Viper with a second blank plate to include if the original owner sells the car).