2023 Dodge Challenger R/t Scat Pack on 2040-cars

Auto blog

Mopar unveils Dodge Challenger Drag Pak [w/video]

Dodge is going drag racing, and it's doing it with an all-new version of the Challenger for NHRA's Sportsman class. FCA's Mopar parts and performance arm announced the new Challenger Drag Pak Friday, showing off a version with a 354-cubic-inch (that's a 5.8-liter, by the way), supercharged V8 and a 426-ci (7.0-liter), naturally aspirated V8 – both Hemis, of course – that can get the big coupes through the quarter-mile in "the eight-second range." While the two engines deliver similar performance, at their base, they're quite a bit different. The supercharged model uses a cast-iron block, while the 426 has aluminum for both the block and head. That said, both models get customized engine calibrations, and are mated to unique, race-spec automatic transmissions. But drag racing is about far more than just outright power. Mopar significantly updated the four-link rear suspension, adding a four-inch rear axle from Strange Engineering, along with an aluminum, nine-inch third member, while the rear-axle housing has been strengthened in general. Both the rear shocks and front struts can be adjusted for rebound and compression, too. Lightweight 15-inch wheels, meanwhile, are shod in super-sticky Hoosier drag radials, with nine inches of tread in back and 4.5 inches in front. The new Challenger Drag Pak should run the quarter-mile in "the eight-second range." In the cabin, there's an NHRA-spec roll cage, a Racepak gauge cluster, and a handsome pair of Sparco racing seats. Outside, supercharged models get blue decals, while naturally aspirated varieties get black stickers, although there's more to the new Challenger dragster's exterior than just its decals. Mopar tweaked the big-scoop hood, promising it's easier to get up to check on the engine, and the designers also added trailer tie-down straps in both the front and rear. While the dragster was the big news today, Mopar officials also announced the two enhanced Scat Pack kits for both the Dodge Charger and Challenger R/T. The 5.7-liter Hemi models gain an extra 56 horsepower and 30 pound-feet of torque in the Scat Pack 2 thanks to a new cam, valve springs, pushrods, and gaskets. The Scat Pack 3, meanwhile, adds 75 hp and 44 lb-ft, on top of the gains from the lower packages. That should be perfect for drivers who wish to snort in the face of their SRT 392-driving friends. The third stage adds a ported cylinder heads, as well as high-flow manifolds and catalysts.

Dodge Journey and Fiat Freemont engine-cover recall affects 350k CUVs

FCA is recalling 349,731 examples of the 2011-2015 Dodge Journey and Fiat Freemont worldwide to better secure their engine covers. Of these affected vehicles, there are 144,416 in the US, 43,679 in Canada, 46,231 in Mexico, and 115,405 elsewhere. About 10 percent of them are also still at dealers, according to the automaker. Only models with the 2.4-liter four-cylinder engine are affected by this campaign. According to the company, the engine covers on these vehicles can be dislodged, and this can pose a fire risk if the loose part comes in contact with hot exhaust components. Warning signs of this happening include a noise under the hood, burning smell or a light on the instrument panel. The problem was discovered after three incidents on rough roads in Chile, and there was one minor injury there. According to FCA US spokesperson Eric Mayne to Autoblog, there have been eight occurrences of this issue reported in the US, but these were all related to "heat damage." There have been no reported injuries here. To fix the problem, dealers will install new engine-cover retainers on the affected models. These repairs will begin in August. As always for recall repairs, owners won't be charged. Statement: Engine Cover July 22, 2015 , Auburn Hills, Mich. - FCA US LLC is voluntarily recalling an estimated 144,416 crossover utility vehicles (CUVs) in the U.S. to better secure their engine covers. Engine covers in certain vehicles may become dislodged. If they come in contact with exhaust components, it may pose a fire risk. This condition was discovered during an FCA US investigation of three incidents in Chile. In each case, the vehicle had been driven extensively on unpaved or uneven surfaces. The Company is aware of a single related injury, described as minor. Affected are 2011-2015 Dodge Journey and Fiat Freemont CUVs equipped with 2.4-liter, four-cylinder engines. FCA US will install upgraded engine-cover retainers in these vehicles. The remedy will be available when customer notification begins next month; service will be performed free of charge. Vehicles equipped with six-cylinder engines are not affected. Additional Journey and Freemont populations also are subject to this campaign. They comprise an estimated 43,679 vehicles in Canada; 46,231 in Mexico; and 115,405 outside the NAFTA region. Of the 349,731 total vehicles subject to this campaign, approximately 10 percent remain in dealer hands.

Dodge Viper to out-Hell the Hellcat with supercharged V10?

The Viper wouldn't be the Viper if it wasn't the most powerful model under the Chrysler umbrella. But with the arrival of the Hellcat engine in the Dodge Charger and Challenger, the Viper has fallen behind in the bragging rights department: where the new supercharged V8 produces 707 horsepower and 650 pound-feet of torque, the naturally aspirated V10 offers "only" 640 hp and 600 lb-ft - gargantuan output figures by almost any other standard, but crucially behind on the SRT power scale. Conner Avenue is going to have to do something about that.
Although the Hellcat's engine reportedly won't fit under the Viper's hood, SRT is now rumored to have another trick up its sleeve: supercharge the existing V10. According to the Pentastar performance enthusiasts at allpar.com, Chrysler has already taken delivery of the first such prototype engines so that it can begin the process of fitting it into an upgraded Viper.
The spooled ten-pot is tipped to produce around 800 hp and 650 lb-ft of torque. More than that and the Viper's drivetrain, chassis and bodywork would have to be substantially reworked. Though beefier transmissions are available, fitting them would reportedly set off a domino-game of changes required to handle the added torque. Which may be something Chrysler would be prepared to do for the next-generation model, but in the meantime, 800 hp could prove enough to put the Viper back atop the Mopar performance ladder where it belongs, and give it an edge against the new Corvette Z06 to rekindle sales.