2013 Dodge Avenger Sxt Sedan 4-door 2.4l Repairable Salvage 7k Miles on 2040-cars

Auto blog

2013-14 Dodge Viper recalled over faulty door handles

The 2013-14 Dodge Viper is getting a voluntary recall affecting 1,762 cars worldwide to replace their door-handle assemblies. Of the affected vehicles, FCA US reports there are 1,451 in the US, 160 in Canada, 17 in Mexico and 59 of them outside of NAFTA. After receiving three reports of doors either not closing or opening while driving a low speeds, FCA US engineers found a new sealant from a supplier didn't provide sufficient moisture protection to the electronic switches for the door latches. If the parts get wet, this can potentially cause a short circuit. The automaker is quite clear that are no reports of accidents of injuries from this problem. As always, the recall repairs will be done at no cost to owners, and FCA US will be getting in touch with customers soon about the problem. Related Video: Statement: Door-handle Assemblies April 9, 2015 , Auburn Hills, Mich. - FCA US LLC is voluntarily recalling an estimated 1,762 cars globally to replace their door-handle assemblies. FCA US launched an investigation after the Company received three warranty claims linked to doors that failed to close or opened inadvertently while vehicles were moving at low speed. The Company is unaware of any related injuries or accidents. Engineers determined a sealant, newly adopted by a supplier, provided inconsistent moisture protection to the electronic switches that control the door latches. Switches exposed to moisture may short-circuit. Affected are approximately 1,451 model-year 2013-14 Dodge Viper SRT cars in the U.S.; 160 in Canada; 17 in Mexico and 59 outside the NAFTA region. Affected customers will be notified and advised when they may schedule service, which will be performed at no cost. Customers with questions may call the FCA US Customer Information Center at 1-800-853-1403.

Chrysler says its 8-speed transmissions will save 700 million gallons

Chrysler Group's TorqueFlite eight-speed transmission could be earning some serious green bragging rights if the company's projections are correct. The recently widely proliferated automatic gearbox, which is now in more than a million vehicles around the world, is poised to save drivers an estimated 700+ million gallons of fuel over the vehicles' lifetimes (an expected cost savings of $2.5 billion). In addition, Chrysler expects a reduction in CO2 emissions by more than six million metric tons. According to Chrysler, and depending on the vehicle, the TorqueFlite can improve fuel economy. The TorqueFlite autobox features particularly close ratios from fifth to eighth gear (see the press release below for the specific numbers), and uses low-viscosity fluid that doesn't need to be replaced. Transmission software adapts to the driving situation to optimize efficiency based on driver behavior, temperature, grade, stability control, and longitudinal and lateral acceleration. The TorqueFlite is capable of handling a variety of duties. As evidenced by the wide range of vehicles Chrysler Group has seen fit to equip with the eight-speed transmission, the TorqueFlite is capable of handling a variety of duties. Since its 2012 introduction, the TorqueFlite has gone from performing cog-swapping duties in Dodge Charger and Chrysler 300 models equipped with the 3.6-liter Pentastar V6 to changing gears in vehicles such as the Pentastar- and Hemi-powered Dodge Durango, Jeep Grand Cherokee and even the Ram 1500 EcoDiesel. For the 2015 model year, the eight-speed is finding its way into even more vehicles with the addition of a third version. In addition to the American-made TorqueFlite 845RE and 8HP70, the new 8HP90 will be manufactured in Saarbrucken, Germany. The 8HP90 is designed for higher torque loads, making it ideal for high-performance vehicles like the 2015 Dodge Challenger SRT Hellcat. The already-in-use 8HP70 will expand its duties to be used in 2015 Hemi models such as the Dodge Charger, Challenger, and Challenger SRT8. You can see the list of those benchmarks in Chrysler's press release below.

How to turn a Dodge airport tug into a trail slayer

Sometimes, having a ton of fun requires takes a ton of work. Just nine days before the so-called Ultimate Adventure 2014, the folks behind 4-Wheel & Off-Road had 40 tasks to complete in order to turn the ratty truck pictured above into a machine that could excel on treacherous off-road trails while still being able to handle highway jaunts. Much of process behind the build was chronicled on the latest episode of Dirt Every Day.
The team's vehicle started life as a 1990 Dodge tug truck that spent part of its life hauling around airplanes. The builders hung on to the Cummins six-cylinder diesel, but they tossed out practically everything else for the project, with some seriously heavy-duty replacement parts for the transmission, transfer case, axles and a whole lot more. The process was certainly a ton of work, but the end result looks like a fantastic crawler.
Sure, it might have been easier to bring a truck that was already prepared, but where would the fun in that have been? Stay tuned until the end of the video for a few glimpses of the completed Dodge and peek at some of the punishment it goes through.