2012 Dodge Avenger Se on 2040-cars

Auto blog

Dodge Challenger spied exercising supercharged Hellcat Hemi V8

One of the prime complaints against the Dodge Challenger is that, even in SRT8 guise, its 470 horsepower is responsible for hauling over 4,200 pounds of vehicle. For comparison, the 420 hp in the Ford Mustang GT only has to deal with 3,618 lbs. Things only get worse from there, as the higher-performance variants of both the Mustang and the Chevrolet Camaro are far more powerful than an SRT8 without adding on much heft.
So what is Chrysler to do? The correct answer is add a whole lot more grunt to its hefty two-door and even the odds. That's where the all-new Hellcat engine comes into play. We reported on this engine in May, and suggested that the Hellcat, a supercharged powerplant based on a 6.4-liter V8, would easily generate 500 to 570 hp and could likely arrive boasting more than 600 ponies.
Chrysler's ace in its sleeve has now been spied testing, with a number of Hellcat-equipped Challengers running the potent new engine both in more urbanized areas and under the sun of Death Valley. The hoods on these testers have been raised to accommodate the engine, and that camouflage over the fascias of these prototypes is there to hide a larger air intake. We also note what appears to be a new split grille under wraps. As for power output, our spies are now suggesting a Viper-equalling 640 hp from the Hellcat-equipped cars.

Chrysler recalling 2009-2010 Ram 1500, Dodge Dakota pickups over axle pinion nut

Chrysler is issuing a recall for the 2009 and 2010 Ram 1500 and Dodge Dakota pickup trucks due to improper installation of the rear axle pinion nut. According to the National Highway Traffic Safety Administration, a total of 44,300 trucks are affected by the recall, and there have been 12 confirmed incidents including one crash.
The issue on both trucks is that the pinion nut is loosening on some trucks due to a lack of thread adhesive, and it is causing the rear axle to lock up resulting in loss of vehicle control. NHTSA's recall notice says that eight incidents occurred at speeds over 35 miles per hour and most also exhibited driveshaft failures as well since the loss of the pinion nut would cause the gear to separate from the driveshaft. In one complaint, the driveshaft separated from the rear axle and punctured the gas tank.
Chrysler will begin sending out recall notices to affected owners in November, but scroll down to see the official NHTSA notice.

Fiat brand chief reassigned then resigns amid flagging sales

Jason Stoicevich was replaced as head of the Fiat brand in North America just the other day. He was immediately reassigned to another job within Fiat Chrysler Automobiles. But according to Automotive News, Stoicevich quit the new job – and the company altogether – the very next day. The development comes amidst flagging sales for the Fiat brand in America. The introduction of the awkward-looking 500L multi-purpose vehicle has been largely regarded as a sales disaster in the US. Despite having just introduced the new 500X into the growing crossover market, and an overall upward trend across FCA group sales, the Fiat brand's figures have been dropping all year. While the Italian brand's volume has fluctuated from month to month compared to last year's sales, the number of cars its dealers sells on an average day has been firmly in decline. Fiat's downward trend reflects a general tendency in the market towards larger vehicles at the expense of smaller ones. However, the powers that be in Auburn Hills evidently felt that a change of leadership was in order, so it placed Dodge chief Tim Kuniskis in charge of all the company's mass-market passenger-car brands – namely Dodge, Chrysler, and Fiat – and moved Stoicevich to running the group's fleet and small-business operations. Stoicevich remained in charge of the company's California Business Center, but it seems as though he was as dissatisfied with the switch as his superiors were with the performance of the brand over which he presided, and so he apparently elected to step down and leave the company.