2012 Chrysler 300 Series on 2040-cars

Auto blog

FCA's Pentastar V6 gets more power, efficiency for 2016

Already a vital member of FCA's powertrain lineup, the 3.6-liter Pentastar V6 is receiving major efficiency improvements for 2016. Thanks to a massive amount of new tech attached to the mill, fuel economy is up six percent, and torque below 3,000 rpm jumps nearly 15 percent. The updates arrive first in the 2016 Jeep Grand Cherokee, but they should proliferate to other models eventually. At least in the Grand Cherokee, the tweaks push power up five horsepower to 295 ponies. FCA's engineers went through the Pentastar from top to bottom to eke out as much efficiency as possible. For example, there's now a two-speed variable-valve lift system that can run in low- or high-lift modes. This upgrade is responsible for 2.7-percent better economy, the company claims. A new intake manifold with longer runners and updated variable-valve times also helps boost the torque output. Further improvements come from pushing the compression ratio to 11.3:1, from 10.2:1 before. Perhaps most impressive is that despite all of the innovations, the latest Pentastar actually weighs four pounds less than the current version. Beyond the Pentastar improvements, all of the FCA US gasoline engines, except for the Viper's 8.4-liter V10, will be E15-compatible for 2016. The company says that it wants to be ready for the higher ethanol content fuel's greater use in the near future.

Towing with the 2016 Ram lineup [w/video]

I do not tow things. Ever. Yet I recently found myself at the Fiat Chrysler Automobiles proving grounds in Chelsea, MI, where I'd be testing the hauling capabilities of Ram's current product range. This experience was not only a perfect education for a towing novice like me, but allowed me to tow far more weight than I'd ever consider hauling the real world, and all within the safe confines of the Chelsea Proving Grounds. There was an extremely diverse array of vehicles at my disposal, including Ram's gasoline- and diesel-powered offerings with trucks ranging from the 1500 on up through the 5500 Chassis Cab, as well ProMaster vans. Beyond that, FCA brought out a number of vintage Dodge pickups for me to play with, while also working with Case IH to provide a track-loader I could test. I put together a range of videos covering everything from the classics to the production trucks to the construction equipment. And despite some technical difficulties – you'll notice a distinct lack of in-car videos, with blame going to a corrupted micro SD card – I've assembled ten videos that give an up-close look at Ram's offerings. 2015 Ram ProMaster City Let's start small. The ProMaster City only has a towing capacity of 2,000 pounds. That's a reasonably impressive figure for a van that uses the same powertrain as a Chrysler 200. The 2.4-liter four-cylinder and nine-speed automatic weren't really bothered with the extra weight added by the trailer. Even when accelerating at freeway speeds, the ProMaster City didn't feel out of breath or hampered by its load. That said, the rear of the van was unloaded, which probably wouldn't be the case for most consumers. It's unclear how the City would feel if its driver were taking advantage of the max payload (1,883 pounds) and towing. 2015 Ram ProMaster 1500 To be polite, the Ram ProMaster is a difficult vehicle to like. Its awkward seating position is bus-like and lacks the visibility enjoyed by the Ford Transit or the utter driving comfort of the Mercedes-Benz Sprinter. Its 3.0-liter, four-cylinder turbodiesel engine, meanwhile, is something of an anomaly. While it's potent for a four-cylinder diesel, producing 295 pound-feet of torque and 174 horsepower, those numbers don't feel all that impressive when loaded down. The model I tested was barely using half of its 5,100-pound maximum towing weight and was loaded down with just 500 of its 3,620-pound payload. Yet it lacked the pluckiness of the smaller City.

Fiat seeking $10B in financing to buy Chrysler

As Fiat looks to become the full owner of Chrysler, all it has standing in its way is the retiree trust of the United Auto Workers, which currently holds the remaining 41.5 percent of the company as the result of the Pentastar's bankruptcy deal. The Detroit News is reporting that that Fiat is currently talking to numerous banks in an attempt to raise around $10 billion to fund the purchase of Chrysler's remaining stake with enough left over to refinance the debt of both companies. We've known that Fiat has been working to obtain the capital to buy out Chrysler for some time now, but this is the first time we've seen Fiat tip its hand about how much cash it thinks it will need to close the deal.
The first order of business is a legal dispute over the value of the UAW's stake in Chrysler, which the report indicates could cost Fiat around $3.5 billion. The acquisition of remaining shares could happen by this summer, but it sounds like CEO Sergio Marchionne (above) might not be ready for a full merger until next year.