2008 Chrysler 300 Touring on 2040-cars

Auto blog

Chrysler says its 8-speed transmissions will save 700 million gallons

Chrysler Group's TorqueFlite eight-speed transmission could be earning some serious green bragging rights if the company's projections are correct. The recently widely proliferated automatic gearbox, which is now in more than a million vehicles around the world, is poised to save drivers an estimated 700+ million gallons of fuel over the vehicles' lifetimes (an expected cost savings of $2.5 billion). In addition, Chrysler expects a reduction in CO2 emissions by more than six million metric tons. According to Chrysler, and depending on the vehicle, the TorqueFlite can improve fuel economy. The TorqueFlite autobox features particularly close ratios from fifth to eighth gear (see the press release below for the specific numbers), and uses low-viscosity fluid that doesn't need to be replaced. Transmission software adapts to the driving situation to optimize efficiency based on driver behavior, temperature, grade, stability control, and longitudinal and lateral acceleration. The TorqueFlite is capable of handling a variety of duties. As evidenced by the wide range of vehicles Chrysler Group has seen fit to equip with the eight-speed transmission, the TorqueFlite is capable of handling a variety of duties. Since its 2012 introduction, the TorqueFlite has gone from performing cog-swapping duties in Dodge Charger and Chrysler 300 models equipped with the 3.6-liter Pentastar V6 to changing gears in vehicles such as the Pentastar- and Hemi-powered Dodge Durango, Jeep Grand Cherokee and even the Ram 1500 EcoDiesel. For the 2015 model year, the eight-speed is finding its way into even more vehicles with the addition of a third version. In addition to the American-made TorqueFlite 845RE and 8HP70, the new 8HP90 will be manufactured in Saarbrucken, Germany. The 8HP90 is designed for higher torque loads, making it ideal for high-performance vehicles like the 2015 Dodge Challenger SRT Hellcat. The already-in-use 8HP70 will expand its duties to be used in 2015 Hemi models such as the Dodge Charger, Challenger, and Challenger SRT8. You can see the list of those benchmarks in Chrysler's press release below.

Hellcrate 6.2-liter V8 delivers plug-and-play Hellcat hype to SEMA

SEMA just provided another entry for the folder marked "What A Time To Be Alive," with Mopar's announcement of the "Hellcrate" 6.2-liter supercharged Crate HEMI engine. Enthusiasts have been desperate to upgrade their vintage rides with the woozy thrills provided by Dodge's Hellcat motor, so Mopar answered. The Hellcrate engine assembly ships in plug-and-play configuration, in specially designed packaging with "Hellcrate" logos. The assembly sells separately from the Hellcrate engine kit, the kit adding a powertrain control module, power distribution center, engine wiring harness, chassis harness, accelerator pedal, ground jumper, oxygen sensors, charge air temperature sensors, and fuel pump control module. The PCM comes programmed with the production-car engine's 707 horsepower and 650 pound-feet of torque. An optional front-end accessory drive kit contributes peripherals like alternator, power steering pump, belts, and pulleys. Don't bother trying to lash up a sleeper 1997 Chrysler Sebring, though; Mopar tuned the Hellcrate for pre-1976 vehicles and manual transmissions. The engine assembly retails for an MSRP of $19,530, and the kit wants a further $2,195. Mopar didn't announce pricing for the accessory drive kit. The engine and kit come with a three-year, unlimited-mileage warranty when bought together. The Mopar Hemi Crate website will be happy to take your orders as of now. For help envisioning the possibilities, stop by Fiat Chrysler's 15,345-square-foot SEMA booth to check out the Limelight Green, Hellcrate-powered 1970 Plymouth Superbird clone worked up by Mark Worman of Velocity's " Graveyard Carz." While you're there you might as well peep Worman's encore, a 1968 Plymouth GTX stuffed with Mopar's 392 Crate HEMI in place of the original 440 big block, and the 1937 Dodge pickup that swallowed a Mopar 345 Crate HEMI. Mopar's come a long way from its original product: antifreeze products. Tomorrow it'll be Jeep's turn to ring the SEMA bells, once the noise dies down from the Mopar-jacked Wrangler Switchback, CJ66 and Jeep Shortcut. You can watch the brand's presentation online at 7:26 p.m. ET/4:26 p.m. PT. Until then, we're going to work the angles on a Hellcrate-powered Plymouth Volare. The sedan, naturally. Because we're practical. Related Video: This content is hosted by a third party. To view it, please update your privacy preferences. Manage Settings.

As it did with Ferrari, Fiat Chrysler spinning off Magneti Marelli

MILAN — Fiat Chrysler said on Thursday its board had tasked management to proceed with spinning off Magneti Marelli and distributing shares in a new holding for the 99-year old parts business to FCA investors. The spinoff is part of a plan by FCA Chief Executive Sergio Marchionne to "purify" the Italian-American carmaker's portfolio and to unlock value at Magneti Marelli, which sits within FCA's components unit alongside robotics specialist Comau and castings firm Teksid, and which analysts say could be worth between 3.6 and 5 billion euros ($4.4-6.1 billion). "The separation will deliver value to FCA shareholders, while providing the operational flexibility necessary for Magneti Marelli's strategic growth in the coming years," Marchionne said in a statement. Magneti Marelli, which employs around 43,000 people and operates in 19 countries, is a diversified components supplier specialized in lighting, powertrain and electronics, and its spinoff is part of a five-year business plan FCA is due to present on June 1. "The spinoff will also allow FCA to further focus on its core portfolio while at the same time improving its capital position," Marchionne added. Marchionne has a long history of such moves. The 65-year-old was behind the spinoff and listing of trucks and tractor maker CNH Industrial and supercar brand Ferrari. The Magneti Marelli separation is expected to be completed by the end of this year or early 2019, with shares in the company expected to be listed on the Milan stock exchange. FCA's advisers initially looked at a possible initial public offering for the business to raise cash to cut FCA's debt, but the Agnelli family - FCA's main shareholder - were put off by low industry valuations and did not want their stake in Magneti Marelli to be diluted, three sources close to the matter told Reuters last month. Magneti Marelli has often been touted as a takeover target and FCA has fielded interest from various rivals and private equity firms over the years. South Korea's Samsung Electronics made a bid approach in 2016 but negotiations fell through as it was only interested in parts of the business, other sources have said. The spinoff is subject to regulatory approvals, tax and legal considerations and a final approval by the FCA board. The carmaker may modify or call off the transaction at any time and for any reason, it added.