Trailblazer Ss on 2040-cars

Auto blog

Leaked GM document shows GMC Sierra I6 diesel is more powerful than F-150's

GM told us earlier this year that the 2019 GMC Sierra would be getting a 3.0-liter I6 diesel option, but it never mentioned power or fuel economy figures. Hold the phone though, because a leaked GM Canada document just showed up online that lists out the details we've been waiting for. Originally published by TFL Truck, the 3.0-liter oil-burner supposedly makes 282 horsepower and 450 pound-feet of torque. For those who are counting, that's more than the Ford F-150's 250 horsepower and 440 pound-feet from its 3.0-liter diesel. It soundly bests the 240 horsepower and 420 pound-feet of torque from Ram's 3.0-liter diesel as well. Fuel economy is another story, though. The promotional material states that it will get 28 mpg on the highway, which is 2 mpg short of the F-150's 30 mpg — mind you, it's only capable of that magical 30 mpg figure in rear-wheel drive form. There's another caveat here, too; these are numbers for Canada, so they're not exactly finalized EPA figures. However, we wouldn't expect drastic differences between the two when the American numbers come out. The leaked documents also state the diesel Sierra will be capable of towing 7,800 pounds. That number seems remarkably low when compared to the F-150, which can tow up to 11,400 pounds with its diesel. Extra power and torque would have us assume that GM could get even better numbers than Ford, so we're going to hold our final judgment for official word. A 10-speed automatic will do the shifting on the diesel, just like on the 6.2-liter V8. Since the Chevy Silverado is also expected to get this engine, we can assume the figures would be almost, if not identical, to those we see here. We recently drove the 2019 Sierra and Silverado without the diesel engines, so go check those reviews out if you'd like to know more of our thoughts on the redesigned GM trucks. Related video:

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM patent reveals new two-stage turbocharger

Modern turbochargers may be some of the best ever made, but performance is something that engineers are always trying to improve. According to GM Inside News, General Motors (GM) is hoping to alleviate some of the negative aspects of a two-stage turbocharger setup with a newly-patented design. The patent, that was filed on May 19, 2016, reveals a clever bypass system that allows the engine, a four-cylinder unit, to optimize both the low-pressure and high-pressure inlets for its respective functions. According to the filing, a conventional two-stage turbocharger setup is engineered to allow both turbines to operate simultaneously at low and mid engine speeds. At high engine speeds, only the low-pressure turbine works. The setup can't isolate either the low or high pressure side, which can impair low-end performance. GM's new two-stage turbocharger setup looks to eliminate this by linking the high-pressure turbo to the exhaust manifold through the high-pressure inlet duct. The low-pressure turbo is attached to the high-pressure turbo by a low-pressure inlet duct, which is linked to a connecting channel. A single actuator that is housed in the exhaust manifold creates a bypass that can opens the high-pressure inlet or close the connecting channel. Depending on what the engine load and speed is, the ECU guides the actuator—a single rotating spindle with discs corresponding to flanges on the high and low pressure sides—to isolate one of the two turbos. Isolating the turbos allow the respective inlets to be engineered for the best possible fluid dynamic performance. The setup should increase performance and decrease lag. There's no word on what car this setup will make an appearance on, but it will most likely be used in premium vehicles before trickling down to the rest of GM's vehicles. Related Video: News Source: GM Inside News, AutoGuide via GM Authority Cadillac Chevrolet GM Technology Sedan turbo patent engine turbocharging