Ls Affordable!!! 4 Dr Suv Automatic Gasoline Vortec 4.2l I6 Sfi With Transmissio on 2040-cars

Auto blog

Reuss says GM diesel plans are still on pace

General Motors is not going to let Volkswagen's diesel emissions scandal ruin its plans for a new line of efficient, torquey oil-burners, the company's Executive Vice President Mark Reuss said at a recent press event. "No way," Reuss responded when asked about cancelling the upcoming diesel-powered Chevrolet Cruze and other vehicles. "The Cruze Diesel is too good not to do it." Slated for 2017, the compact is just the latest member of a diesel offensive that initially kicked off with the first Cruze Diesel and most recently saw the introduction of the oil-burning Chevy Colorado and GMC Canyon. Reuss also reassured those in attendance that there was "no delay" in development of Cadillac's diesel lineup. Cadillac is working on a line of four- and six-cylinder turbodiesels for Europe. They'd make their way into the US market, too, eventually. "It's a question of timing," Reuss said, according to Car and Driver. Volkswagen's diesel emissions scandal has caused automakers across the globe to at least reanalyze their diesel strategy. Jaguar Land Rover, which is preparing several diesel-powered models for the US market, went on record late last month to reaffirm its commitment to diesel. Related Video: Featured Gallery 2014 Chevrolet Cruze Turbo Diesel: Quick Spin View 14 Photos News Source: Car and DriverImage Credit: Copyright 2015 Seyth Miersma / AOL Green Cadillac Chevrolet GM Diesel Vehicles

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Why an independent rear suspension for GM's new, full-sized SUVs wasn't easy

A Motor Trend report last month laid out how Cadillac's 4.2-lier twin-turbo Blackwing V8 could be an orphan due to cost concerns in the GM empire. Last-minute chassis changes to Cadillac's new sedans and XT6 crossover led to engine bays that couldn't fit the Blackwing. On the SUV side, according to the report, the new independent rear suspension for big people haulers cost so much to implement that GM ruled out reworking the Escalade to accept the Blackwing. At least one commenter rightly asked how could a suspension swallow that much money. A new piece in Motor Trend has the answer. The excellent Alissa Priddle spoke to Tim Herrick, GM's executive chief engineer for full-size trucks, about why the clean-sheet IRS cost "multimillions of dollars."  First, GM would need to build a new body shop at the Arlington, Texas plant that assembles the automaker's big SUVs to stamp the numerous wholly new parts and panels accommodating an IRS. Then GM would need to design and pay for a new assembly process. On top of those up-front costs, there was the incremental cost of the four-link IRS components being more expensive than those in the trucks' former leaf-sprung solid axles. Herrick endured so many rejections for so long that he remembers the date and time when he got approval for the new unit. He said it came down to a meeting where he told a higher-up, "I'll make you a deal: If we get to the reveal, or if we launch this and you think this was a dumb idea, I'll hand you my badge and let you walk me out." Head to Motor Trend to read the full story. Based on Herrick being on stage to help present the new SUVs to the press, and on our First Ride in the new Chevrolet Tahoe and Suburban at GM's Milford Proving Grounds, it appears this will have a happy ending for all involved. Furthermore, since Herrick worked on the T1 platform that supports the big SUVs as well as the light- and heavy-duty pickups, he understood the demands on the commercial side, too. That could be why when Roadshow asked Tim Asoklis, chief engineer of the Tahoe and Suburban, if the new IRS could endure life in the Chevrolet Silverado and GMC Sierra, Asoklis answered, "Oh, absolutely." Related Video: