2008 Chevrolet Tahoe Hybrid Sport Utility 4-door 6.0l on 2040-cars

Auto blog

New Takata problem results in recall of 414 GM vehicles

An airbag-inflator rupture discovered by Takata during testing has resulted in a new recall affecting 414 vehicles from General Motors, including 395 of them in the US. This latest campaign covers 2015 model-year examples of the Buick LaCrosse, Cadillac XTS, Chevrolet Camaro, Equinox, Malibu, and GMC Terrain. There are no reported breaks in any of these vehicles on the road, and the company estimates only one percent of them actually have the faulty parts. According to documents submitted to the National Highway Traffic Safety Administration (as a PDF), one side-airbag inflator failed a cold test at -40 Fahrenheit "releasing high pressure gas and propelling the separated components apart." The supplier told GM about the failure the next day. In these vehicles, the safety device might not only burst but the bag could inflate incorrectly, as well. GM and Takata say that a cause is not yet known, but they are "conducting an investigation." GM will begin notifying affected owners via overnight mail on Oct. 19. Dealers will replace the side airbag modules on all of the affected vehicles with new components outside of the suspect lot. All of the removed parts will also be collected for further study. Takata's faulty front airbag inflators have resulted in a serious scandal for the supplier. Initial figures indicated 34 million US vehicles are need of repair, though more recent figures have knocked that down to 23.4 million bad parts in 19.2 million automobiles. GM was already among the dozen automakers with models to fix, and some of its pickups were affected, along with the Saab 9-2X and Pontiac Vibe. GM Statement: General Motors is recalling 395 cars and crossovers in the U.S. because one of the front seat side air bags inflators may be defective. In the event of a deployment, the air bag's inflator may rupture and the air bag may not properly inflate. The rupture could cause metal fragments to strike the vehicle occupants, potentially resulting in serious injury or death. GM is unaware of any incidents involving vehicles with these components, which were part of a lot in which one inflator failed acceptance testing at the supplier. Dealers will replace the side air bag module or modules in affected vehicles. Including Canada, Mexico and exports, the total population of the recall is 414, GM estimates 1 percent of the recalled vehicles may have the defect.

Meet the mother-daughter team that's worked on almost every Chevy Volt

It's Mother's Day, and we're soft enough we love our mothers enough to share a new video from General Motors with you. In it, we meet Monique Watson (left) and Evetta Osbourne, a mother-daughter team that works at the Detroit-Hamtramck Assembly where GM makes the Chevy Volt (along with all of GM's other plug-in hybrids: the Opel Ampera, Holden Volt and Cadillac ELR). The two work side-by-side and have installed the lithium-ion battery pack on almost all of those vehicles - nearly 80,000 of them - since GM started making the pre-production Volts in 2009. In a prepared statement, Watson said that she likes working next to her mom, day in and day out, and they the two are totally in sync when it comes to putting the 400-pound, 16.5-kWh packs into the vehicle undersides. They two can also share stories throughout the day, and Watson said, "The arrangement has absolutely improved our relationship." Osborne started working at Detroit-Hamtramck in 1999, Watson since 2006. If you're driving a Volt today, you probably have them to thank for doing a bit of the work putting your car together. See a short video of them in action below. It's Always Mother's Day for Detroit-Hamtramck Duo Mother, daughter install lithium-ion battery pack in nearly all GM electric vehicles 2014-05-08 DETROIT – For Detroit resident Evetta Osborne, every day is Mother's Day. That's because she literally works side by side with her daughter, Monique Watson, at General Motors' Detroit-Hamtramck assembly plant. They have installed the lithium-ion battery pack on nearly every Chevrolet Volt, Opel Ampera, Holden Volt, and Cadillac ELR since production began. In fact, apart from vacation days and an occasional sick day, the mother-daughter duo has installed almost every battery pack since the Volt was in pre-production in 2009. The ELR launched earlier this year. All told – including Ampera – that's more than 80,000 electric vehicles. "We're a good team and our relationship is secondary when it comes to performing our jobs – but it's great to work alongside my daughter, said Osborne, a mother of five. Because the battery packs weigh more than 400 pounds each, automatic guided vehicles – robotic carts that use sensors to follow a path through the plant – deliver them just as the vehicle body structures glide into position overhead. The carts then lift the T-shaped packs, and Osborne and Watson guide them into the chassis and secure each one with 24 fasteners.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck