Silverado 3500 4x4 Crew Cab Diesel on 2040-cars

Auto blog

Race Recap: Rolex 24 at Daytona was fast and feisty

Let the record show that victory at the 2015 Rolex 24 at Daytona went to the No. 02 Chip Ganassi Racing with Felix Sabates Target/Ford EcoBoost Riley DP driven by Verizon IndyCar drivers Scott Dixon and Tony Kanaan and NASCAR drivers Jamie McMurray and Kyle Larson. The winner did 740 laps to cover 2,634.3 miles in 24 hours and 57.667 seconds. That's a statement to this year's pace in spite of 18 cautions, two more than last year: the Michael Shank Racing Ligier got pole with a time of 1:39.194, slower than last year's pole time of 1:38.270; however, the winning car last year only did 695 laps. The fight for top honors was shaved to a four-car battle over the first third of the event. The No. 02 Ganassi car took the lead on the first lap, swapping it well into the night with the No. 01 Ganassi car, the No. 10 Wayne Taylor Racing Corvette DP, and the defending champion No. 5 Action Express Corvette DP, all of them staying within about 20 seconds of one another. The Action Express car had a fuel connector come loose and lost three laps getting towed back to the pits to have it reattached, but was back in the lead 18 hours in. The No. 01 Ganassi car dropped out with recurring clutch problems 22 hours in, retiring not long after. A race-within-the-race is where the concluding action happened, a seven minute, 30-second dash from the end of the last caution to the checkered flag. During the penultimate pit stops with an hour to go, Dixon was in second place followed Jordan Taylor in the Wayne Taylor Racing DP into the pits but beat him out, taking the lead. The Action Express car was in third. In the last pit stops of the race, Dixon gained even more time, getting a four-second advantage over Taylor. Then a full-course caution came out twenty minutes before the finish when a Prototype Challenge car hit the wall and caught fire, bunching up the field. That closed the pits, but the Wayne Taylor Racing car had to pit during that yellow because of a miscalculation of driver time. No driver can be behind the wheel for more than four hours in a six-hour period but Jordan Taylor was going to go over, so he came in to swap out for brother Ricky. That cost the team any chance of second place, since they took an additional drive-through penalty for entering closed pits. When the track went green again, Sebastien Bourdais in the Action Express car stayed all over Dixon for the final five laps but couldn't get around him.

"Turbo" Chevrolet Camaro is a 700-HP fantasy car come to life [w/video]

For a concept car built to promote an animated movie about a snail that wants to go racing, this thing ain't half bad. The outsized monster you see before you started life as a Chevrolet Camaro ZL1, and then went through a big-time Hollywood makeover before being positioned on the Chevrolet stand here in Chicago.
This 2013 "Turbo" Camaro Coupe is getting the promotion machine ratcheted up for a new DreamWorks tale by the name of, you guessed it, Turbo. Coming this summer, the movie will follow one snail's quest to become a race driver worthy of making the cut at the Indy 500. Like many DreamWorks vehicles before it, we're guessing that the petrolhead snail will star in a movie that adults (especially racing fans) with have no trouble watching with their kids. Check out the trailer below to see if you agree.
As for the car, we're told that it is "instrumental" in transforming Turbo from snail into racer. Helping the beastly pony car in this mighty task, is an ankle-cracking front splitter matched by a ungodly huge rear wing out back, a COPO hood and a supercharged (yes, supercharged) V8 engine making more than 700 horsepower. 24-inch wheels all the way around - 10-inches wide in front and 15-inches wide in back - should allow the "Turbo" Camaro to hook up with ease, as well.

Our favorite mid-engine Corvette theories and rumors

The mid-engine Corvette! We just saw blurry photos through the foliage, and are hearts are all aflutter because it means that this car is real. And it's the most " never before" Corvette since 1984. Which leads us to all kinds of wacky theories and speculation. Everybody knows something or heard from a guy. None of those guys (or gals) from GM are talking to Autoblog, to be clear. But that won't stop us from stirring the pot. Let's go over a few point-by-point. The pushrod engine will be replaced by an overhead-cam V8 Car and Driver has repeatedly reported that an overhead-cam engine will come after the mid-engine Corvette's debut with an old-school pushrod. We've heard the same thing firsthand, albeit from a source with no connection to the development of the Corvette or powertrain. "At some point two valves can't pass future emissions regulations," said the guy we know. While the pushrod engine is compact, the design makes it difficult - if not impossible - for sophisticated variable valve timing (and lift) systems that control combustion with more precision. Hasty conclusion: The pushrod engine has a finite life in front of it. This one's a lock, it's a just a matter of when. Bowling Green's new paint shop is really the mid-engine assembly line Credit to Reddit for this one. Like we said, everybody knows a guy. But let's look deeper. The new paint facility costs $439 million dollars and adds 450,000 square feet, almost half the size of the existing plant. Plus GM announced another $290 million in upgrades at Bowling Green Assembly. That sure sounds like a lot of money, but you can actually spend that much on a paint booth. Porsche spent 500 million Euros (about $561 million dollars) to add the Macan assembly to its Leipzig, Germany plant in 2014. Chrysler shelled out $850 million for a paint shop in Sterling Heights, Michigan. GM spent $600 million for a new paint shop at the Fairfax (Kansas City) plant. Honda, on the other hand, is working on a thrifty $210 million project in Marysville, Ohio that includes a 300,000 square foot expansion, and the low-volume Acura NSX facility only cost $70 million. Hasty conclusion: The square footage and cost could easily mean a new assembly line instead of (or in addition to) a paint line. And if the NSX plant was really that cheap, GM could have hidden a similar sum in its existing announcements.