Chevy Crew Cab Duramax Diesel 4x4 Ltz Custom New Lift Wheels Tires Leather Auto on 2040-cars

Auto blog

Chevy's 6.6-liter Duramax is pretty much all new

To say there's a heated battle in heavy-duty pickups is an understatement, with Chevrolet, Ford, and Ram constantly trading blows of increased torque, horsepower, and towing capacity. The latest salvo is the revised, more powerful turbo diesel 6.6-liter Duramax V8 in the 2017 Chevy Silverado. It has 910 pound-feet of torque, an increase of 145, putting it nearly level with the Ford Super Duty. Here's a closer look at where those gains come from. How exactly did Chevrolet add all that torque plus 48 horsepower? The automaker essentially took a fine-tooth comb to the entire engine. Chevy says it changed 90 percent of the V8, and the cumulative effect of those small changes adds up to big increases. As you might guess, the turbocharger is updated. The larger unit features electric actuation of the variable nozzle turbine (VNT), and what Chevy calls a double axle cartridge mechanism that separates the VNT moving parts from the housing. That helps with heat performance as well, with a claim that the exhaust side of the turbo can run continuously up to 1,436 degrees Fahrenheit. Helping that cause are six exhaust gaskets made of Inconel - an nickel alloy that contains chromium and iron – and upgraded stainless steel for the exhaust manifold. Despite having the same cast iron cylinder block, albeit with some minor enhancements, the engine has new cylinder heads, pistons, piston pins, connecting rods, and crankshaft, which have all been upgraded to handle 20 percent higher cylinder pressures. Alongside the increase in pressure, Chevrolet also increased the cylinder head's structure with a honeycomb design. The pattern features high-strength aluminum with dual layer water jackets that not only improve strength, but also optimize water flow for better cooling. For 2017, the cylinder head also benefits from integrated plenum that aids the engine in getting more air under heavy loads. The cylinder head isn't the only component to get a minor update, as the pistons have a larger diameter pin for improved oil flow. The same detailed improvements has been bestowed to the humble connecting rods (second in our hearts only to the inanimate carbon rod). The new design has the bolts oriented roughly 45-degrees to the rod instead of parallel. The angle split design, as it's called allows for easier passage through the cylinder.

More Corvette Stingray Factoids: Vanishing panel gaps and 26-mpg LT1

During January's Detroit Auto Show, we managed a longer than expected wandering tag-team interview with C7 Corvette chief engineering exec Tadge Juechter (pictured above), and LT1 engine boss Jordan Lee (pictured below). They are, quite honestly, two of the very nicest bigshot lads to ever walk the engineering corridors of an American manufacturer. Both are enthralled by what they're doing for a day job. So are we.
We've followed the pre-sale anticipation for the Chevrolet C7 Corvette Stingray like an Oreck vacuum yanking every speck of dirt from a well-trampled carpet. Everything is reportable and contains a grain of further knowledge about this dramatically important and cheered-for car, as it continues to be pressured into representing all that is superior about the American dream. The Corvette wears one heavy cloak.
So, most of what was talked about has been expertly reported already right here on Autoblog. But, looking through our notes again, both Jeuchter and Lee added facts to the buzzing mix.

GM, UAW poaching Nissan workers in Tennessee

General Motors and the United Auto Workers are going on a recruitment drive at the Spring Hill factory in Tennessee, and they're hoping to poach some skilled workers from Nissan's nearby plant in Smyrna, TN. The General and the union even bought a billboard advertising for industrial electricians near the Japanese automaker's facility, according to the Daily News Journal. The reason for the billboard was simple. "GM was short of electricians," said Tim Stannard, the president of the UAW local at Spring Hill, to the Daily News Journal. The factory currently builds the Chevrolet Equinox but has a contract to assemble the next generation of Ecotec engines and the Cadillac XT5, which replaces the SRX. Thanks to the $185-million deal, employment there is expected to double by May 2016, according to Stannard, with roughly 1,800 additional union jobs. Beyond just several billboards, GM has job postings online for the Spring Hill plant looking for workers with specific skills. There has already been some interest in the positions among Nissan employees, Stannard indicated. According to a recent study by the Center for Automotive Research, the average GM worker currently makes $58 an hour, including benefits. Comparatively, Nissan pays an average of $42 an hour with benefits. The General's number could change in the coming weeks because its contract with the UAW is about to expire, and higher wages are among the major negotiating points.