2000 Chevy Work Truck Reg Cab Long Box on 2040-cars

Auto blog

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

Leak reveals GM's 2017 heavy duty diesel trucks to get 910 lb-ft of torque [UPDATE]

UPDATE: Chevrolet officially announced specs for the 2017 Silverado HD and the rumors were true. The truck's new Duramax 6.6-liter turbo-diesel V8 puts out 445 horsepower and 910 pound-feet of torque. Chevrolet says the new motor produces 19 percent more torque and 12 percent more horsepower, while producing 35 percent fewer emissions. Overall, the new engine is a big improvement over the current motor, which generates 397 horsepower and 765 pound-feet of torque. According to Truck Trend, GM's newest heavy duty pickup trucks will pick up quite a bit more power and torque. The publication spotted a recent GM Powertrain ordering catalog that had the engine specs for the 2017 model year and managed to get some screenshots before the catalog was taken down, and they can be viewed here. The screenshots revealed that the 6.6-liter turbodiesel V8 powering the Silverado and Sierra heavy duty models will boast 445 horsepower and 910 lb-ft of torque. This is a substantial gain over the current models' 397 horsepower and 765 lb-ft of torque, and as Truck Trend points out, it exceeds the Ford Super Duty line's horsepower output of 440, but comes short of the 925 lb-ft rating. Truck Trend credits part of this output gain to the new intake system GM will introduce on the 2017 heavy duties. The intake gets 60 percent of its air from a scoop on the hood, with the other 40 percent coming from behind one of the front fenders. GM doesn't reveal horsepower figures in the press release about the scoop, but it does say the cooler air helps with maintaining the engine's output, and that the scoop does produce a ram-air affect, providing more air at speed. As we know, more air plus more fuel equals more power, but there's likely more to the power increase in this engine than only the intake. Related Video: News Source: Truck Trend via MSN Chevrolet GM GMC Truck Diesel Vehicles

GM cutting Chevy Sonic, Buick Verano production [UPDATE]

UPDATE: A previous version of this story indicated that Orion Assembly would be idled for seven weeks, from February 16 through April 6. This was incorrect. The factory will instead only be idled for the weeks of February 16 and April 6. The story has been edited to reflect this. General Motors has announced that the factory responsible for the Buick Verano and Chevrolet Sonic will be idled for the weeks of February 16 and April 6, with blame being placed on excess supply. The Orion Assembly plant, about 45 minutes north of GM's Renaissance Center headquarters, employs about 1,800 people, but they'll be given a pair of furloughs as inventories of the sub-compact Sonic and premium compact Verano reach 127 days and 84 days, respectively. That works out to 26,600 Chevys and 9,800 Buicks waiting for buyers. According to Automotive News, the compact Chevy sales bested the industry average in 2014, jumping up nine percent versus the the overall segment's eight-percent gain, while the Buick sedan's sales were down four percent. When asked about the shutdown, a GM spokesman told AN that it will "build to market demand," while also pointing out that the company did not comment on production plans. News Source: Automotive News - sub. req.Image Credit: Bill Pugliano / Getty Images Plants/Manufacturing Buick Chevrolet GM buick encore orion assembly