4wd Auto Texas Air Tan White Dual Zone Climate Control Low 65k Miles Interior on 2040-cars

Auto blog

GM throttles back Chevy Malibu, Buick LaCrosse production over swollen inventories

As inventory of the Chevrolet Malibu and Buick LaCrosse continues to pile up, General Motors will be idling its Fairfax Assembly Plant for two weeks, according to Automotive News. This move comes about a month after the plant was shut down for three weeks in late December and early January for the same reason. As of January 31, the GM had a 94-day supply of Malibu stock while the LaCrosse was a little worse with a 117-day supply.
Just last week, GM announced that it would be investing $600 million in upgrading this plant, but it's unclear what future plans the company has in store for Fairfax considering slow sales of both the plant's models. We do expect a refreshed and more luxurious LaCrosse shortly and an early design update for the Malibu to be announced at some point this year, although we have had no official word as to when either will happen.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Chevy Sail 3 lands in China

Shanghai General Motors took 32 cars to this year's Guangzhou Motor Show, with its Chevrolet Sail 3 leading the way. After putting almost 1.4 million of them into Chinese hands, the third generation of the Bowtie's entry-level sedan wants to "take the nameplate and the segment to a new level." Its new architecture sporting a 1.4-inch longer wheelbase supports a growth spurt of two inches in length and 1.8 inches in width. The exterior also gets "eagle eye-shaped" headlights and "dual-c-element taillights." Under the hood will be either a 1.5-liter DVVT or a 1.3-liter VVT, each of them more powerful and more frugal than previous offerings. Both can be paired with a manual or an automatic transmission, and qualify for listing in China's National Energy-Saving and Eco-Friendly Vehicle Catalogue, as well as a 3,000 renminbi rebate ($490 US). You can read more about it in the press release below, and get more info on the Chevrolet Camaro RS Limited Edition, Corvette Stingray Coupe, Buick Regal GS and Excelle XT also introduced at the show. Chevrolet, Buick and Cadillac Take Center Stage at Guangzhou Auto Show - New Chevrolet Sail 3, Camaro RS Limited Edition and Corvette Stingray Coupe make China debut - Buick showcases customized Regal GS and Excelle XT - Shanghai GM announces new telematics strategy featured in upcoming Cadillac product GUANGZHOU, 2014-11-20 – Shanghai GM is displaying 32 vehicles from the Chevrolet, Buick and Cadillac brands at the 12th Guangzhou International Auto Show, which begins today and runs through November 29 in Guangzhou. Among the products that are making their China debut are the third-generation Chevrolet Sail 3, Chevrolet Camaro RS Limited Edition and Chevrolet Corvette Stingray Coupe. In addition, Buick is showcasing a customized Regal GS and Excelle XT, and Shanghai GM is announcing its new telematics strategy that will be featured in an upcoming Cadillac product next year. Chevrolet Sail 3 Entry-Level Family Car Since its introduction 15 years ago, the Sail has been a driving force in the entry-level family car segment. Nearly 1.4 million Sails have been sold across China. The third-generation Chevrolet Sail, named the Sail 3, will take the nameplate and the segment to a new level when it goes on sale nationwide by the end of this year. Built on Shanghai GM's new-generation small car architecture, the Sail 3 has adopted Chevrolet's new design language. It has a sculpted yet slim exterior with a youthful, dynamic feel.