2014 Chevrolet Silverado 1500 Lt on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Fewer than 1 in 3 Chevy dealers earn right to initially sell C7 Corvette

Looking to make the launch of the 2014 Corvette Stingray as efficient as possible, Chevrolet will be limiting the numbers of its dealers that can sell the all-new coupe and convertible. According to Automotive News, sales of the C7 Corvette will initially be limited to less than a third of Chevy's total dealership network when the 'Vette goes on sale this summer.
Only 900 dealers out of more than 3,000 locations nationwide will be allowed to sell the new Corvette at first, and the reason for this is so that there are no shortages at dealers that can actually get the cars sold. The article says that the 900 dealerships chosen represented 80 percent of total Corvette sales in 2012.
Some of the requirements dealers had to make to get initial allocation of Stingray sales include having sold at least four Corvettes in 2012 and having a Corvette Stingray specialist who will be required to have gone through a training session costing more than $2,000 per attendee. Once demand for the 2014 Corvette Stingray begins to subside - approximately six to nine months after it goes on sale - then allocation could open up to more dealers, but the report indicates this could happen following the 2014 model year.

GM Design shows what could have been and what might be

We periodically like to check in with GM Design's Instagram account to see what they're cooking up. Even better is when we catch a glimpse of an alternate history of what legendary designers from The General's past were thinking, though those ideas may not have made it into production. This week, for example, the account posted some illustrations from George Camp, whose career at GM spanned nearly four decades, from 1963 to 2001. One of the renderings is of what appears to be a 1971-72 Pontiac GTO Judge, but with two headlights instead of the production unit's quad beams. The rear departs from the canonical version most dramatically, with a massive integrated wing. Other bits that didn't make the production cut include large side vents, a gill-like side marker and rectangular intakes below the headlights that wouldn't be out of place on a modern design today. Amazingly, from what we can make out of the date, it appears that the drawing was done sometime in 1965, which makes it quite prescient.           View this post on Instagram                       A post shared by GM Design (@generalmotorsdesign) There's also a very aerodynamic interpretation of a Corvette ZR-1. To our eyes it splits the difference between the 1986 Corvette Indy concept and a fourth-generation F-body Pontiac Firebird, so perhaps parts of Camp's work on this sketch did make it into physical form. There's also a radical sports car concept from May 1970 that resembles the Mazda RX-500 concept from the same year, a Syd Mead-looking Cadillac coupe, and an Oldsmobile with a cool take on the company's trademark waterfall grille and elements of the Colonnade Cutlass at the rear. Other recent posts include a FJ Cruiser-like off-road EV, a sleek coupe with the Chevy corporate grille, and a rendering of a Silverado-esque pickup that looks far better than the current production version.           View this post on Instagram                       A post shared by GM Design (@generalmotorsdesign) It's pretty easy to lose hours in the account, but it's always fascinating to see GM's visions of what could have been and what might be. Related Video: