2011 Chevy Silverado Ltz Crew Z71 Leather Rear Cam 36k! Texas Direct Auto on 2040-cars

Auto blog

Corvette Z06 and Viper TA square off at the strip

There are many long-standing grudge matches among automobiles: 911 vs GT-R, Mustang vs Camaro, Ferrari vs Lamborghini... but as far as high-end American metal goes, it doesn't get much more legendary than Viper vs 'Vette. So after Chevy released the new Corvette Z06, we knew it was only a matter of time before it would have to square off against the Viper TA. And what better place to pit these two parallel pillars of American performance than on the drag strip? Fortunately that's just what we have here. In one corner, the 2014 Dodge Viper TA, with its 8.4-liter V10 pumping out 640 horsepower and 600 pound-feet of torque. In the other, the 2015 Chevrolet Corvette Z06, the supercharger on its 6.2-liter V8 more than making up for the discrepancy in displacement and cylinder count to produce 650 hp and just as much torque. But numbers don't tell the whole story, so watch the video clip to see which reaches the end of the quarter-mile first. News Source: To the Floor via YouTubeTip: James Chevrolet Dodge Videos drag race chevy corvette z06 quarter mile drag strip srt viper ta

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

Watch this time-lapse build of the Chevy SS for NASCAR

There's only about a week left until we get our first look at the production version of the 2014 Chevrolet SS sedan, but Chevrolet NASCAR teams have been looking at the race version of the car all winter. Autoweek has posted a really neat time-lapse video showing just a portion of what it takes to build one of NASCAR's new Gen6 stock cars.
Though the video is quite brief, it does show almost the entire build process starting with just the car's nose, and it gives us a good look at how integral the template is to the final product. As a bonus, Hendrick Motorsports also provided some videos showing two of its teams performing pit stop tests over the winter. The second video shows some of the more detailed aspects of the racecar's rear end, including the stock-looking trunk cutout and a newly mandated rear bumper extension that will be used on super speedways like Daytona and Talladega.
To see what Team Chevy has been up to all off-season, check out all three videos posted after the jump.