2006 Chevrolet Silverado 1500 Lt on 2040-cars

Auto blog

Camaro spy shots show subtly different grille, front fascia

It looks like there some changes in store for the Chevrolet Camaro - the only thing is that we just don't know what Chevy has up its sleeve. Looking at these spy shots, we'd initially be inclined to think that there is just a minor facelift or a new special edition, but upon closer inspection, there are a few oddities about this car that definitely have us intrigued.
The most obvious difference on this prototype is the slightly restyled front fascia with a smaller lower air inlet and the two-bar grille. Then we get to some of the car's mysterious details. For starters, this fascia has the SS vent above the grille, but it looks to be blocked off. Granted this could just be a one-off piece used for testing. What really piqued our interest was at the rear of the car where it has quad exhaust outlets that are used on the ZL1. Could this be the LS7-powered Camaro that we reported on back in December?
At this point, your guess is as good as ours as to what we're looking at here, so let us know in the comments what you think this could be.

Common Dodge Ram 1500 vs. Chevrolet Silverado breakdowns

These two trucks are famous for their ability to get the job done. Still, even the toughest vehicle can have mechanical problems at some time. What if we match the Dodge Ram 1500 and Chevrolet Silverado head to head? Let's find out more about common repairs for each model. Also, learn some tricks to pay for car repairs. Clunky Steering Both Dodge and the Chevy owners sometimes notice bumping and clunking when steering. This might be more noticeable when driving over bumps. The cause is usually different in each truck though. In the Dodge Ram, clunky steering is more likely due to a defective lower ball joint. Replacement costs around $300 - $400, parts and labor. Clunky Chevy Silverado steering is probably a steering rack failure. This problem appears more often in trucks with over 90,000 miles. Silverado steering rack repair will run you up to $1,000 or more. Starting Woes For the Chevy Silverado with over 130,000 miles, you might notice trouble starting. This problem may appear occasionally at first, but it typically gets worse. Excluding a weak battery, the culprit is usually the starter. Replacement will cost you around $330 - $500. Of the total cost, $90 is for labor only. Now the Dodge Ram might make a ticking sound when starting, especially on models with over 94,500 miles. The noise often disappears after the engine warms up. These symptoms may indicate a broken exhaust manifold. Repair costs range from $800 - $900. Burning Oil & Gas Gauge On The Blink Sometimes, the Dodge Ram burns oil much faster than normal. In models with over 125,000 miles, this often points towards a leaky intake manifold gasket. A knocking sound may also appear with acceleration along with possible engine misfire. The cost to repair is around $200 - $300. The Chevy Silverado has its own surprises, especially when you've filled the gas tank but the gauge still reads low. Or the needle fluctuates widely from low to full while driving. In trucks with over 120,000 miles, it's likely due to a faulty fuel sensor. You might need a full fuel pump replacement, which can cost you up to $820, parts and labor. Water Inside And Poor Heat The Ram 1500 rear window has been known to leak. You might notice the back seat and floor wet after a rainstorm. This is more common in trucks with over 65,000 miles. Resealing the Ram 1500 rear window costs around $150 - $250.

GM adds 1,200 jobs at Detroit-Hamtramck plant

General Motors is making a big move at its Hamtramck, MI, factory, announcing it will add a second shift and hire over 1,200 workers within the next several months. It's expected that by early 2016, the factory will employ over 2,800 workers to build the Chevrolet Volt, Impala, Malibu, Cadillac ELR, and by early next year, the new CT6. According to GM Hamtramck spokesperson Courtney Zemke, 40 of the 1,200 positions are for salaried employees, while the remainder will be hourly positions. As for where these employees will go, positions are being made available across the factory, so GM isn't focusing on any particular area for its new hires. It's a similar story behind the hiring surge itself. GM said in its press release that the "second shift is necessary to meet forecasted market demand," a position Zemke reiterated. It's a matter of demand across the plant's portfolio, rather than any one particular product seriously outstripping supply. Naturally, the United Auto Workers is happy with the move. "The workforce at Detroit-Hamtramck is second to none," UAW Local 22 Shop Chairman Don LaForest said in the attached release. "We appreciate the opportunity to expand our UAW-GM family." Hiring is going on now, with the second shift slated to get underway in early 2016. GM's Detroit-Hamtramck Assembly to Add Second Shift and More Than 1,200 Jobs Plant will nearly double its workforce by early 2016 2015-10-22 DETROIT – General Motors is nearly doubling its workforce at Detroit-Hamtramck Assembly by adding a second shift and more than 1,200 hourly and salaried jobs. The addition of a second shift will increase the plant's workforce to approximately 2,800 people when hiring is completed. The second shift is necessary to meet forecasted market demand for the five cars produced at Detroit-Hamtramck. "This is the result of the award-winning vehicles Detroit-Hamtramck produces and the confidence GM has in our team to build world-class quality for our customers," said Plant Manager Gary West. Second shift hiring is underway, and the shift is scheduled to begin operations in early 2016. "The workforce at Detroit-Hamtramck is second to none," said UAW Local 22 Shop Chairman Don LaForest. "We appreciate the opportunity to expand our UAW-GM family." The 4.1 million-square-foot Detroit-Hamtramck Assembly opened in 1985. GM has invested $1 billion in the plant over the last six years, making it one of the company's most-agile manufacturing facilities in North America.