~~03~chevy~silverado~stepside~rare~ls~reg~cab~lifted~5.3l~no Reserve~~ on 2040-cars

Auto blog

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

GM veteran Bryan Nesbitt tapped to head Buick design

General Motors styling veteran Bryan Nesbitt (pictured above) took over a new role on Monday as executive director of global Buick design and global architectures. Andrew Smith, who previously did that job and also coordinated the look for Cadillac, has remained in charge of the pen at Caddy with this shift. Nesbitt rose to prominence when he designed the Chrysler PT Cruiser, according to Automotive News. He joined GM in 2001 and has been there ever since in multiple high-level roles. In 2007, he was appointed vice president of design for North America and was later briefly general manager of Cadillac in 2009-2010. Nesbitt took over as the vice president of GM's international operations design in China in 2011. This shuffle also moves Ken Parkinson, currently styling boss for Chevrolet trucks, to China as design vice president there. In addition, John Cafaro becomes the person in charge of the look for Chevy globally, rather than previously splitting that role between cars and trucks with Parkinson. GM Global Design Leadership Changes – effective June 1, 2015. Bryan Nesbitt, Design Vice President, GM China will repatriate to North America and assume the position of Executive Director, Global Buick and Global Architectures. He will be located in Warren, MI. Bryan will be the design Champion for Buick in the US and China. Ken Parkinson, Executive Director, Global Chevrolet Trucks and Global Architecture will assume the position of Design Vice President, GM China. He will be based in Shanghai, China. Andrew Smith, Executive Director, Global Cadillac and Buick Design will assume the position of Executive Director, Global Cadillac. He will continue to be the design Champion for the Cadillac brand. In addition, he will continue to lead the Global Color & Trim team. He will be based in Warren, Michigan. John Cafaro, Executive Director, Global Chevrolet Cars will assume the position of Executive Director, Global Chevrolet. He will be the design Champion for Chevrolet. In addition, John will lead the exterior components and accessories team. He will continue to be based in Warren, MI. The roles and responsibilities of Helen Emsley, Mark Adams, Carlos Barba, Clay Dean, Michael Simcoe, and Teckla Rhoades remain the same. Related Video: The video meant to be presented here is no longer available. Sorry for the inconvenience.

GM to squeeze out more production capacity for midsize trucks

General Motors was predicting a strong showing for the Chevrolet Colorado and GMC Canyon before they debuted, and demand among dealers for the midsize trucks even exceeded company's expectations. The positive situation has left GM with a problem, though: finding ways to increase capacity for the pickups at the Wentzville Assembly plant in Missiouri. With a third shift already running, GM has continued to look for ways to build just a few more of the trucks at the plant. The company has plans to hire as many as 1,000 more workers for the Saturday and Sunday shifts to construct an additional 2,000 pickups a month, according to unnamed insiders at the factory speaking to Automotive News. The little adjustments even extend to getting rid of an unpaid break to add 18 minute of assembly time over the course of a day, which equals about 3,500 more vehicles a year. All of this effort comes because the trucks are in such high demand. According to GM's figures, the company has delivered a combined 35,720 units of the Colorado and Canyon from January through April 2015, and the Chevy was the fastest-selling truck in the US for the previous three months. In May, it spent an average of just 12 days in showrooms before being snapped up. And even better for the company, 43 percent of these buyers came from other brands. According to Automotive News, the most popular trade-ins have included the Ford F-150, Toyota Tacoma, and Dodge Dakota. Related Video: