1999 Chevrolet S10 Lt1 V8 on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Final C6 Corvette built in Bowling Green

With all of the attention given to the 2014 Chevrolet Corvette Stingray lately, you could be forgiven for thinking that it's already well along in production, yet tooling up for the new C7 has only just begun. In fact, production of the outgoing C6 generation in Bowling Green, Kentucky just halted on Thursday.
As the C6 has aged, production numbers have predictably ebbed along with demand, but this year, the addition of the 427 and 60th anniversary models resulted in an uptick in vehicles built - this, despite a model year shortened by around 25 percent to accomodate the new model changeover. The final C6 Corvette ever, No. 13,466 built this year, was a white 427 Convertible destined for the General Motors Heritage Center museum. The car's 7.0-liter V8 heart was assembled by Corvette chief engineer Tadge Juechter himself.
In total, Bowling Green pushed out 215,100 C6 Corvettes over nine years. If you're still a C6 fan at heart and are hoping to get a good deal on a phase-out model, step lively - Chevrolet reportedly had about 6,100 unsold units, which Autoweek suggests is good for around five and a half months of supply at the model's current sales rates. Given that demand will likely slacken even further as the C7 draws closer, that should be a big enough stockpile to keep dealers satisfied until 2014 Stingrays begin showing up on their forecourts in December.

GM to build outgoing Silverado and Sierra until late 2019

As it has done with previous generations, General Motors is keeping the outgoing versions of its 1500 pickups in production despite the arrival of the all-new 2019 Chevrolet Silverado and 2019 GMC Sierra. The production of the previous, K2 generation models will begin to be wound down gradually, according to Automotive News, starting with crew cabs "early next year," and double and regular cab models following during "the early second half of next year." The old model trucks will continue to be built into "late 2019" based on market demand, GM's spokesperson Kim Carpenter said. The Chevrolet will go by the name Silverado LD, with the GMC Sierra designation still to be announced. Some of the outgoing models are built by sharing the assembly work between two GM plants. Partially finished Silverado and Sierra double cab bodies are shipped from Fort Wayne, Ind., to Oshawa, Ont., where the trucks are completed, including receiving paint. This eases the workload in Fort Wayne, where production of the new T1 generation trucks started in July 2018. In January, the Silao plant in Mexico will take on the duties of building new generation regular cab and crew cab trucks. Carpenter also said that the "Oshawa shuttle," as the shared production is called, has been very successful. As a result, 60,000 more trucks will be built than what the original production forecast initially called for. GM's latest quarterly profits, disclosed last week to be $1 billion, have been far higher than expected and will result in full-year profits far higher than what had been predicted in light of steel tariffs. GM isn't the only truck maker taking a similar multi-generation approach for 2019. Both the outgoing and redesigned Ram 1500 are in production, with the previous generation being dubbed Ram 1500 Classic. Related Video: