1964 Red Chevy Pick-up on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM seeks national mandate for zero-emissions cars

DETROIT — General Motors says it will ask the federal government for one national gas mileage standard, including a requirement that a percentage of auto companies' sales be zero-emissions vehicles. Mark Reuss, GM's executive vice president of product development, said the company will propose that a certain percentage of nationwide sales be made up of vehicles that run on electricity or hydrogen fuel cells. GM says a nationwide program modeled on such a requirement in California could result in 7 million electric vehicles, or EVs, on U.S. roads by 2030. California wants 15.4 percent of vehicle sales by 2025 to be EVs or other zero emission vehicles. Nine other states, including Maryland, Massachusetts, New Jersey and New York, have adopted those requirements. In January, California Governor Jerry Brown set a target of 5 million zero-emission vehicles in California by 2030. The Trump administration criticizes California's ZEV mandate, saying it requires automakers to spend tens of billions of dollars developing vehicles that most consumers do not want, only to sell them at a loss. Reuss told reporters that governments and industries in Asia and Europe "are working together to enact policies now to hasten the shift to an all-electric future. It's very simple: America has the opportunity to lead in the technologies of the future." A national mandate also would create jobs and reduce fuel consumption, CO2 emissions and "make EVs more affordable," Reuss added. GM, the nation's largest automaker, will spell out the request Friday in written comments on a Trump administration proposal to roll back Obama-era fuel economy and emissions standards, freezing them at 2020 levels instead of gradually making them tougher. Under a regulation finalized by the Environmental Protection Agency at the end of the Obama administration, the fleet of new automobiles would have to get 36 miles per gallon by 2025, 10 mpg higher than the current requirement. But the Trump administration's preferred plan is to freeze the standards starting in 2021. Administration officials say waiving the tougher fuel efficiency requirements would make vehicles more affordable, which would get safer cars into consumer hands more quickly. GM on Thursday said it doesn't support the freeze, but wants flexibility to deal with consumers' shift from cars to less-efficient SUVs and trucks.

Chevy Tahoe-to-K5 Blazer conversion shop renders Jimmy option

Back in 2019 we told you about a truck that looked like a K5 Chevy Blazer, but was actually a modern late-model Tahoe underneath. It was the product of Arkansas shop Flat Out Autos, which reskinned modern GM full-size SUVs to look like their predecessors. Now, the same shop is planning to release a GMC version, converting Yukons to Jimmys. We were impressed by Flat Out's workmanship, beautifully blending the lines of the Blazer into those of the Tahoe. The result was a cohesive design, not just a panel swap. It clearly required a lot of work, which helped justify the $69,000 price tag, not including the cost of the donor Tahoe. FlatOut Autos GMC Blazer Tahoe reskin 01 View 11 Photos At least one new owner was so impressed that they recently purchased four identical Blazer conversions at once. The quadruplets were all finished in blue with a white roof and all based on brand-new 2020 Tahoes. Obviously, with such demand it was only natural for Flat Out to explore other options. On Facebook the company said it was working on a 1972 version with an eggcrate grille. Now, they've also released a rendering paying homage to the K5 GMC Jimmy. The Jimmy conversion uses the original's quad-headlight face, crosshair grille and GMC badging. Like the Blazer conversion, it adds chrome bumpers and milled door handles while adapting the original's 2-door design to the new truck's 4-door body. The rendering only shows the front three-quarter view, but presumably a new carbon fiber rear door would have to be created as the Blazer's says "Chevrolet" across the back. Flat Out says that all the modern conveniences found on the donor Tahoe will work on the conversion, including parking, blind spot and lane keeping sensors. If you have the coin, it's a great way to have retro style without giving up modern safety and performance. The new Blazer has been disappointing to many fans that had hoped for a Bronco-like SUV. Instead, GM gave us a crossover. The Flat Out conversions might be a good compromise, and expanding it to the GMC brand only makes sense. Obviously there's no requirement to use a GMC Yukon as the donor vehicle for the Jimmy, as it's functionally identical to a Tahoe, but wouldn't you want to keep it in the family? Related Video: