Awesome 1972 Chevy Nova Ss Clone Ready To Drive!!! on 2040-cars

Auto blog

1983 Motorweek showdown pits Porsche 928S vs. Chevy Camaro Z28

Last month, Motor Trend threw the Camaro Z/28 and Porsche 911 GT3 into the bear pit and let them fight it out. Way back in 1983, MotorWeek had the same idea, comparing the Camaro Z/28 to the Porsche 928S. At the time, the Camaro was America's best selling sports coupe, the 928S was Porsche's top-of-the-line model that also had the highest top speed of any car sold here. And the price differential was even more stark then: $13,600 for the Camaro, $45,000 for the Porsche. That put the Z/28's cast-iron, 5.0-liter V8 with 190 horsepower and 240 pound-feet of torque against the all-aluminum 4.7-liter V8 with 234 hp and 263 lb-ft in the 928S. Even with that and the Camaro being 14 inches longer than the Porsche, the American was a surprising 40 pounds lighter than the German. The show took them to Summit Point Raceway in West Virginia to see how close a relative performance bargain could hang with a the German GT. Both had five-speed manual transmissions, but the high-speed corners and tight sections of Summit Point would test other handling variables, including the "bone-rattling" Camaro's solid rear axle and disc and drum brake setup vis-a-vis the four-wheel disc brakes and independent suspension on the "firm-but-smooth" Porsche. Paradoxically, the larger disparity 22 years ago resulted in a closer result. Check out the video to see how the Summit was won. News Source: MotorWeek via YouTube Chevrolet Porsche Coupe Luxury Performance Classics Videos chevy camaro z28 porsche 928 retro review

Burt Reynolds' vehicles up for auction at Barrett-Jackson

Burt Reynolds' influence on car culture cannot be overstated. Be it "Smokey and the Bandit" or "Cannonball Run," his films inspired a generation of car enthusiasts. He died a few weeks back from cardiac arrest at age 82. This weekend, four vehicles from Reynolds' personal collection — three Pontiacs and a Chevy — will go up for auction at Barrett-Jackson in Las Vegas. It seems Reynolds had plans to sell the cars before he passed. He even filmed a short teaser for the auction and planned to attend the event himself. Three of the cars are Pontiac Trans Ams. Two are re-creations of the cars he drove in "Bandit" and the film "Hooper." Both are 1978 models. The third Trans Am is from 1984 and was used to promote Reynolds' USFL team, the Tampa Bay Bandits. The fourth vehicle is a 1978 Chevy R30 pickup truck. It's styled like the truck he drove in "Cannonball Run." None of the vehicles were actually used in the movies. But they were registered in his name, making them far more legitimate than some other movie-inspired clones. It's unclear how many Bandit Trans Ams Reynolds has owned over the years. Another car connected to him sold for $450,000 back in 2014. His death is sure to drive the price of these new cars even higher. Related Video: Image Credit: Barrett-Jackson Celebrities Chevrolet Pontiac Auctions Truck Coupe pontiac trans am burt reynolds

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck