2014 Chevrolet Malibu 1lt on 2040-cars

Auto blog

Camaro spy shots show subtly different grille, front fascia

It looks like there some changes in store for the Chevrolet Camaro - the only thing is that we just don't know what Chevy has up its sleeve. Looking at these spy shots, we'd initially be inclined to think that there is just a minor facelift or a new special edition, but upon closer inspection, there are a few oddities about this car that definitely have us intrigued.
The most obvious difference on this prototype is the slightly restyled front fascia with a smaller lower air inlet and the two-bar grille. Then we get to some of the car's mysterious details. For starters, this fascia has the SS vent above the grille, but it looks to be blocked off. Granted this could just be a one-off piece used for testing. What really piqued our interest was at the rear of the car where it has quad exhaust outlets that are used on the ZL1. Could this be the LS7-powered Camaro that we reported on back in December?
At this point, your guess is as good as ours as to what we're looking at here, so let us know in the comments what you think this could be.

Cadillac Celestiq, Lyriq, Hummer, other future GM electric cars: Here's everything we saw at ‘EV Day’

WARREN, Mich. — Today, General Motors held an “EV Day” event at its Warren, Michigan, campus to present its new “Ultium” battery technology, modular electric vehicle architecture and soon-to-come electric vehicles. Unfortunately, we were forbidden from bringing cameras into the event, so while we canÂ’t show you what we saw, we can tell you more about it. While we saw the previously teased Cadillac EV (which we now know to be called the Lyriq) and the GMC Hummer pickup teased during the Super Bowl, there were a number of other future cars at the event, which GM President Mark Reuss assured us are all real vehicles in the works. The biggest surprise came at the end of the event, though, in the Cadillac Celestiq electric sedan, which Reuss described as a future flagship that would be hand-built “very locally.” It had been hiding under a dark sheet all morning, with the front and rear illuminated Cadillac emblems shining from underneath. When the wraps came off, we saw a long, white, four-seat fastback sedan. The 23-inch wheels were pushed out to the very corners of the car, giving it what appeared to be a very long wheelbase. The model on the stage had no side mirrors or visible door handles. The grille mirrored that of the Lyriq crossover next to it, with integrated lighting in lieu of the usual mesh or slats youÂ’d see in an internal combustion car. The entire roof, all the way until it tapered to the tail of the vehicle, was tinted glass. In back, vertical tail lighting ran down the C-pillar before turning rearward across the top of the trunk. Inside, everything below the beltline of the windows — essentially all but the headrests and top portion of the steering wheel, was hidden from view. Behind the Celestiq, a large digital display showed a rendering of its interior. The dash consists of a pillar-to-pillar curved LED display serving as both instrument panel and infotainment system. Protruding forward between the front seats was another touchscreen that appeared to house some more controls, with open area, probably for storage, below it. The rear seats had the same sort of touchscreen between them. Built into the back of the front seats were a pair of rear-seat entertainment screens, much like we saw in the Lyriq. The door panels blended wood, metal and animated lighting to give character and a sense of opulence. GM interior design manager Tristan Murphy was on hand to tell us a bit more about the Celestiq.

UAW to vote on strike at Kentucky Corvette plant

The current wait time for a new Chevrolet Corvette Stingray is well, not short. With word of a strike at the Bowling Green, KY factory responsible for seventh-generation sports car, though, that wait time could end up growing substantially.
Now, a strike is still a ways off. UAW Local 2164, which represents the 800 workers responsible for screwing the Corvette together, is set to vote on authorizing a strike today, but even if the employees give the action a go, it's far from a sure thing. According to The Tennessean, both regional and national union officials would need to put their stamp of approval on strike action.
"The membership has to vote to strike, but it's just a step in the process," said Gary Casteel, the UAW's Region 8 director and one of the people that would need to authorize a strike action. Casteel told The Tennessean, "It's purely a local situation, though. They are having some issues with the local management."