2011 Chevrolet Malibu 1lt on 2040-cars

Auto blog

Chevy admits there's confusion over Bolt and Volt names

Offering the possibility of 200 miles of driving range and the potential for a price of about $30,000, the Chevrolet Bolt is an incredibly enticing vehicle, and it has an opportunity to be a big player in the EV world. However, the hatchback has been plagued by one problem since the moment it debuted – the name. Bolt sounds very similar to Volt, Chevy's extended-range plug-in, and they can be easy to confuse in a conversation. That's not the best quality to have when trying to get a new vehicle's name out there among customers, and General Motors North America president Alan Batey told the Detroit Free Press that the company is aware of the problem. While the EV is definitely going into production, the model might be wearing a different moniker when it hits showrooms. "We're still in the decision phase. It could go either way," Batey said to the Free Press. He indicated the automaker still has about a year before a final decision is necessary. The Bolt will be built at GM's Orion Assembly plant in Michigan and will likely go on sale around 2017. That will put the Chevy on the market at roughly the same time as the 200-mile Tesla Model 3. Batey didn't seem too concerned, though. "Unlike Tesla, we can spread the cost over a whole lineup," he said to the Free Press. The future doesn't look quite so bright for the Spark EV, though. Batey suggested that it might not last once the longer-range Bolt fills that niche in the lineup. Related Video:

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

Watch this time-lapse build of the Chevy SS for NASCAR

There's only about a week left until we get our first look at the production version of the 2014 Chevrolet SS sedan, but Chevrolet NASCAR teams have been looking at the race version of the car all winter. Autoweek has posted a really neat time-lapse video showing just a portion of what it takes to build one of NASCAR's new Gen6 stock cars.
Though the video is quite brief, it does show almost the entire build process starting with just the car's nose, and it gives us a good look at how integral the template is to the final product. As a bonus, Hendrick Motorsports also provided some videos showing two of its teams performing pit stop tests over the winter. The second video shows some of the more detailed aspects of the racecar's rear end, including the stock-looking trunk cutout and a newly mandated rear bumper extension that will be used on super speedways like Daytona and Talladega.
To see what Team Chevy has been up to all off-season, check out all three videos posted after the jump.