2014 Chevrolet Impala 2lz on 2040-cars

Auto blog

Race Recap: Rolex 24 at Daytona was fast and feisty

Let the record show that victory at the 2015 Rolex 24 at Daytona went to the No. 02 Chip Ganassi Racing with Felix Sabates Target/Ford EcoBoost Riley DP driven by Verizon IndyCar drivers Scott Dixon and Tony Kanaan and NASCAR drivers Jamie McMurray and Kyle Larson. The winner did 740 laps to cover 2,634.3 miles in 24 hours and 57.667 seconds. That's a statement to this year's pace in spite of 18 cautions, two more than last year: the Michael Shank Racing Ligier got pole with a time of 1:39.194, slower than last year's pole time of 1:38.270; however, the winning car last year only did 695 laps. The fight for top honors was shaved to a four-car battle over the first third of the event. The No. 02 Ganassi car took the lead on the first lap, swapping it well into the night with the No. 01 Ganassi car, the No. 10 Wayne Taylor Racing Corvette DP, and the defending champion No. 5 Action Express Corvette DP, all of them staying within about 20 seconds of one another. The Action Express car had a fuel connector come loose and lost three laps getting towed back to the pits to have it reattached, but was back in the lead 18 hours in. The No. 01 Ganassi car dropped out with recurring clutch problems 22 hours in, retiring not long after. A race-within-the-race is where the concluding action happened, a seven minute, 30-second dash from the end of the last caution to the checkered flag. During the penultimate pit stops with an hour to go, Dixon was in second place followed Jordan Taylor in the Wayne Taylor Racing DP into the pits but beat him out, taking the lead. The Action Express car was in third. In the last pit stops of the race, Dixon gained even more time, getting a four-second advantage over Taylor. Then a full-course caution came out twenty minutes before the finish when a Prototype Challenge car hit the wall and caught fire, bunching up the field. That closed the pits, but the Wayne Taylor Racing car had to pit during that yellow because of a miscalculation of driver time. No driver can be behind the wheel for more than four hours in a six-hour period but Jordan Taylor was going to go over, so he came in to swap out for brother Ricky. That cost the team any chance of second place, since they took an additional drive-through penalty for entering closed pits. When the track went green again, Sebastien Bourdais in the Action Express car stayed all over Dixon for the final five laps but couldn't get around him.

Weekly Recap: BMW rolls out ambitious plug-in hybrid electric plan

"We believe that for the United States, this is going to be very important." – Julian Arguelles Let there be no doubt, BMW is serious about electric vehicles. The German automaker said this week it will make plug-in hybrid versions of all of its core models, an aggressive move that demonstrates its commitment to electric propulsion systems. BMW did not specify which vehicles will get the plug-in systems or provide a timeline for when they will arrive. But the announcement is clearly more than blustering, and the company revealed a 3 Series plug-in prototype this week at an event in France. BMW said the 3 Series uses a version of its 2.0-liter turbocharged four-cylinder engine (240 horsepower, 300 pound feet of torque) with an electric motor sandwiched between the engine and transmission in place of the torque converter. It has an all-electric range of 22 miles. A plug-in X5 with the same powertrain was also displayed alongside the 3 Series, though the X5 has been on the auto-show circuit for more than a year, including a recent stop in Los Angeles. Those two vehicles use "eDrive," and BMW's plans represent the first widespread transfer of its technology from development of the i3 and i8 models to more mainstream products. BMW said it's developing electric powertrains so they can be deployed rapidly across its range, and they are flexible enough to be used with fuel cells in future products. Enticingly, BMW is also working on a "Power eDrive" system, which debuted in a 5 Series GT concept at the event in France. This setup has two electric motors powered by a 20-kilowatt-hour battery pack, and when teamed with a four-cylinder turbo, pump out about 670 hp. Reinforcing BMW's commitment, the company will add more than 200 jobs at its factory in Dingolfing, Germany, to support electric-vehicle development. The moves come as BMW and other automakers diversify their portfolios while fuel economy and emissions regulations are getting tighter around the world. The United States has set a 54.5-mpg CAFE requirement for the 2025 model year. BMW said the electric vehicles were developed with an eye toward the US market, its government policies and its wide-ranging commuting styles. "We believe that for the United States, this is going to be very important," spokesman Julian Arguelles said. Ben Scott, a senior analyst in London with automotive research firm IHS, said BMW's moves are expensive – but necessary – to keep pace with the market.

GM recalls 8,500 Chevrolet Malibu models for rear suspension glitch

According to a letter from General Motors to the National Highway Traffic Safety Administration, flaws in the build process of the 2013 Chevrolet Malibu have led to the recall of 8,519 cars. Units built between December 6, 2011 and January 15, 2013 may have been assembled with rear suspension cradles that had insufficient torque applied to certain bolts. That out-of-spec assembly could lead to issues ranging from slight noises to a loss of vehicle control.
The problem was first noticed in December of last year by a GM test fleet driver and eventually tracked back to the improperly torqued bolts on the suspension cradle assembled through July 2012 by a supplier located not too far from the Malibu's Detroit/Hamtramck Assembly Plant. Since an official NHTSA recall notice has not been issued yet, it isn't clear whether or not Detroit-built Malibus were the only ones affected (the 2013 Malibu is also built at GM's Fairfax Assembly Plant in Kansas City, Kansas). Dealers will fix the problem by inspecting vehicles for proper torque specs, retightening if not within specs and, in some cases, perform a rear-wheel alignment.