2009 Chevrolet Hhr Ls Panel Wagon 2-door 2.2l on 2040-cars

Auto blog

Chevy's 6.6-liter Duramax is pretty much all new

To say there's a heated battle in heavy-duty pickups is an understatement, with Chevrolet, Ford, and Ram constantly trading blows of increased torque, horsepower, and towing capacity. The latest salvo is the revised, more powerful turbo diesel 6.6-liter Duramax V8 in the 2017 Chevy Silverado. It has 910 pound-feet of torque, an increase of 145, putting it nearly level with the Ford Super Duty. Here's a closer look at where those gains come from. How exactly did Chevrolet add all that torque plus 48 horsepower? The automaker essentially took a fine-tooth comb to the entire engine. Chevy says it changed 90 percent of the V8, and the cumulative effect of those small changes adds up to big increases. As you might guess, the turbocharger is updated. The larger unit features electric actuation of the variable nozzle turbine (VNT), and what Chevy calls a double axle cartridge mechanism that separates the VNT moving parts from the housing. That helps with heat performance as well, with a claim that the exhaust side of the turbo can run continuously up to 1,436 degrees Fahrenheit. Helping that cause are six exhaust gaskets made of Inconel - an nickel alloy that contains chromium and iron – and upgraded stainless steel for the exhaust manifold. Despite having the same cast iron cylinder block, albeit with some minor enhancements, the engine has new cylinder heads, pistons, piston pins, connecting rods, and crankshaft, which have all been upgraded to handle 20 percent higher cylinder pressures. Alongside the increase in pressure, Chevrolet also increased the cylinder head's structure with a honeycomb design. The pattern features high-strength aluminum with dual layer water jackets that not only improve strength, but also optimize water flow for better cooling. For 2017, the cylinder head also benefits from integrated plenum that aids the engine in getting more air under heavy loads. The cylinder head isn't the only component to get a minor update, as the pistons have a larger diameter pin for improved oil flow. The same detailed improvements has been bestowed to the humble connecting rods (second in our hearts only to the inanimate carbon rod). The new design has the bolts oriented roughly 45-degrees to the rod instead of parallel. The angle split design, as it's called allows for easier passage through the cylinder.

Final C6 Corvette built in Bowling Green

With all of the attention given to the 2014 Chevrolet Corvette Stingray lately, you could be forgiven for thinking that it's already well along in production, yet tooling up for the new C7 has only just begun. In fact, production of the outgoing C6 generation in Bowling Green, Kentucky just halted on Thursday.
As the C6 has aged, production numbers have predictably ebbed along with demand, but this year, the addition of the 427 and 60th anniversary models resulted in an uptick in vehicles built - this, despite a model year shortened by around 25 percent to accomodate the new model changeover. The final C6 Corvette ever, No. 13,466 built this year, was a white 427 Convertible destined for the General Motors Heritage Center museum. The car's 7.0-liter V8 heart was assembled by Corvette chief engineer Tadge Juechter himself.
In total, Bowling Green pushed out 215,100 C6 Corvettes over nine years. If you're still a C6 fan at heart and are hoping to get a good deal on a phase-out model, step lively - Chevrolet reportedly had about 6,100 unsold units, which Autoweek suggests is good for around five and a half months of supply at the model's current sales rates. Given that demand will likely slacken even further as the C7 draws closer, that should be a big enough stockpile to keep dealers satisfied until 2014 Stingrays begin showing up on their forecourts in December.

GM reintroduces Tripower name in the worst way possible

The story of General Motors' use of the Tripower moniker begins way back in 1957, when Semon E. "Bunkie" Knudsen, then General Manager of GM's Pontiac division, directed his engineers to inject more performance into his brand's line of V8-powered automobiles. Fuel injection was an option, but hot rodders flocked instead to Tri-Power (marketed way back when with a hyphen), which grafted a trio of two-barrel Rochester carburetors onto a single intake manifold. A legend was born. And that legend was born of performance. At idle and when full power wasn't required, Pontiac's Tri-Power system used just the middle carburetor, which helped make the setup easier to tune. Depending on the year and model, either a vacuum system or a mechanical linkage opened up the two outer carbs, thereby switching from two barrels to six, and allowing the engine to take in more fuel and air. And it was an easy marketing win – six barrels is better than four barrels, right? Because performance! So, when news filtered in that GM has resurrected the Tripower name, those of us who grew up attending classic car shows and wrenching on old Pontiacs did a double-take. And then we all collectively sighed. Turns out that today's Tripower refers to a trio of fuel-saving measures that include cylinder deactivation, active thermal management, and intake valve lift control, according to Automotive News. And, at least for now, it applies to GM's line of fullsize trucks powered by a 2.7-liter turbocharged four-cylinder engine. We're all for saving fuel whenever possible. And we have zero say in how any automaker chooses to market its products and technologies. But, we'll offer our two cents anyway: Relaunching a storied name from the past is fine. Relaunching a storied name from the past while completely overlooking the reasons the name got famous in the first place is only going to irritate the people who remember the name in the first place. Couldn't they just call this new technology package something else? Related Video: News Source: Automotive NewsImage Credit: Getty Green Marketing/Advertising Chevrolet GM Pontiac Automotive History Truck chevrolet silverado