2013 Chevrolet Express Cargo 1500 Stabilitrak on 2040-cars

Auto blog

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

GM patent reveals new two-stage turbocharger

Modern turbochargers may be some of the best ever made, but performance is something that engineers are always trying to improve. According to GM Inside News, General Motors (GM) is hoping to alleviate some of the negative aspects of a two-stage turbocharger setup with a newly-patented design. The patent, that was filed on May 19, 2016, reveals a clever bypass system that allows the engine, a four-cylinder unit, to optimize both the low-pressure and high-pressure inlets for its respective functions. According to the filing, a conventional two-stage turbocharger setup is engineered to allow both turbines to operate simultaneously at low and mid engine speeds. At high engine speeds, only the low-pressure turbine works. The setup can't isolate either the low or high pressure side, which can impair low-end performance. GM's new two-stage turbocharger setup looks to eliminate this by linking the high-pressure turbo to the exhaust manifold through the high-pressure inlet duct. The low-pressure turbo is attached to the high-pressure turbo by a low-pressure inlet duct, which is linked to a connecting channel. A single actuator that is housed in the exhaust manifold creates a bypass that can opens the high-pressure inlet or close the connecting channel. Depending on what the engine load and speed is, the ECU guides the actuator—a single rotating spindle with discs corresponding to flanges on the high and low pressure sides—to isolate one of the two turbos. Isolating the turbos allow the respective inlets to be engineered for the best possible fluid dynamic performance. The setup should increase performance and decrease lag. There's no word on what car this setup will make an appearance on, but it will most likely be used in premium vehicles before trickling down to the rest of GM's vehicles. Related Video: News Source: GM Inside News, AutoGuide via GM Authority Cadillac Chevrolet GM Technology Sedan turbo patent engine turbocharging

McLaren, Koenigsegg, Toyota, Ford, Dodge and Corvette Lego kits announced for 2021

Lego has announced a slew of car-themed sets for 2021. The six kits comprise nine vehicles and fall under the brick pusher's Speed Champion line of official OEM-licensed kits. News of their arrival comes from German toy retailer JB Spielwaren's pre-order listings, which show three single-car sets and three dual-car sets of matched marques. Starting with the McLaren Elva roadster, the kit consists of 263 pieces and is finished in blue. It seems to have a difficult time capturing the curves of the real-life Elva, but there's only so much you can do with a bunch of plastic blocks. Lego has made several other McLaren kits before, including the Senna, 720S, and a more advanced Senna GTR for the Technics line. Next up is the Koenigsegg Jesko, made up of 280 pieces and finished in white. Though the real-life Jesko is still curvy, this kit does a better job of replicating its aggressive maw, vents and cantilevered rear wing. Rounding out the single-car sets is the 299-piece Toyota GR Supra in yellow. This marks the first time Toyota has lent their license to Lego. Again, it struggles a bit to represent the curvy Supra, relying on printed details like logos and headlights to identify. On the other hand, the Chevrolet two-car does a stupendous job with the 1968 Corvette. The C3 is instantly recognizable as such. The C8-R race car it's paired with suffers from the same issues as some of the previous cars, though. The set contains 512 pieces, and funnily enough the C8 driver has short hair while the C3 driver sports a period-correct wavy mane. The next set is a 627-piece Mopar-themed pair, including a purple (Plum Crazy?) 1970 Dodge Challenger T/A and an SRT top fuel dragster. The race car is spot on, but the Challenger was probably tough to make given the width restrictions. It looks a couple of pegs too narrow compared to the wide proportions of the real deal. Last but not least, the Ford set contains a Bronco R and Ford GT Heritage Edition. Consisting of 660 pieces, the set does an excellent job of representing both cars. The GT looks faithful in its Gulf livery, and the Bronco R looks more like a real Bronco than the actual Bronco R race truck. All in all, it's always fun to see more Lego sets with real cars, and we're glad to see more manufacturers added to the roster. The single-car sets are recommended for ages 7 and up, while the double-car sets have an 8 years and up rating. Price in U.S.