Chevrolet Cruz Two Air Bag Right Side,belt Right Side, on 2040-cars

Auto blog

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

Recharge Wrap-up: EV torque secrets, UC Davis maps future of biofuels

A UC Davis white paper maps out "Three Routes Forward for Biofuels," balancing investment risk with carbon benefits. The first option is "incremental," in which we tinker with the existing biofuel manufacturing infrastructure for small improvements over time. The "transitional" plan suggests integrating cellulosic production and other innovations with existing operations. The third route, called "leapfrogging," would mean building refineries based on new technology such as cellulosic and algae-based biofuels. The paper suggests ways the US could use these three routes together in different areas, and predicts the payoffs in terms of carbon emissions could be significant if the right people are willing to risk the capital. After all, financial advisers are always telling investors to diversify their portfolios to manage risk and rewards in the same way. Read more over at the UC Davis Institute of Transportation Studies. The Formula E Long Beach ePrix will offer free admission. The seventh round of the inaugural all-electric race season, which was moved from Los Angeles to the streets of Long Beach, will offer fans free grandstand and general admission. The race, which takes place on April 5, 2015, will use a 1.6-mile portion of IndyCar's Grand Prix of Long Beach. Read more at LA Times. Polaris is now offering its 2015 GEM electric vehicles, including the new street-legal eM1400 LSV. The passenger and utility vehicles come in two- to six-passenger configurations, many of which are street legal on roads with posted speed limits of up to 35 miles per hour. The eM1400 LSV utility vehicle seats two, offers 1,250 pounds of payload, 1,250 pounds of towing capacity, a top speed of 25 mph and a range of up to 45 miles. Its on-board charger plugs into any standard 110-volt outlet. Read more at Hybrid Cars and check out all the different configurations yourself at the Polaris website. In EVs, more torque does not always equal faster. Green Car Reports found this out when driving the Fiat 500e (with 147 pound-feet) against the similarly weighted Chevrolet Spark EV (with 400 pound-feet). The secret is, at least in part, in the gearing. The Fiat has a 9.6:1 reduction gear, making it quicker at lower speeds despite having far less available torque, while the Chevy uses a 3:1 ratio. The trade-off though, is in top speed. Furthermore, Chevy electronically limits the torque delivery at low speeds, as 400 pound-feet is a lot of launch for the little Spark EV to handle.