2014 - Chevrolet Corvette on 2040-cars

Auto blog

How GM engineers are using diaper 'snow' to keep you warm

Testing how snow affects General Motors' vehicles isn't really a problem right now for the company's engineers, but in the dog days of summer the process isn't exactly easy. The only real option is for them to book time at the automaker's climatic wind tunnel. However, a flash of brilliance from an engineer allows snow to be simulated regardless of the temperature outside, and the discovery is all because of his daughter's wet diaper. The realization came to GM Thermal Systems engineer Nicholas Jahn while he was swimming with his daughter and noticed how her diaper ballooned in size in the water. He found out the substance that makes this possible is called sodium polyacrylate. When the material gets wet it grows and forms fluffy flakes that are a close imitation of snow. Best of all, the stuff can be prepared easily any time of the year, and it's reusable. The engineering team uses the material to test the effectiveness of the heating systems of GM's vehicles. They spread the sodium polyacrylate over the inlets at the base of the windshield to obstruct the airflow and then crank the heater. After some time, they can see how much is being sucked into the system and design more efficient systems in the future. See how the process works in the video above and read about the diaper discovery in GM's press release below. Diapers Change Chevy Cruze Winter Warm-up Time GM validation engineer uses diaper material "snow" to reduce frigid drives 2015-01-06 DETROIT – An item commonly found on an infant's changing table is helping General Motors' engineers simulate snow year round, ensuring heating systems in cars like the 2015 Chevrolet Cruze can quickly and efficiently warm its interior. Packed snow can prevent air from entering the inlet panel at the bottom of the windshield, obstructing the flow of air into the heating system and reducing the amount of air it can push out. This can lead to less efficient warming of the car's interior and windshield defrosting. "The last thing anyone wants to do when it's freezing cold out is scrape their windshield," said Nicholas Jahn, GM Vehicle Thermal Systems engineer. "The testing we perform on the Chevrolet Cruze with the diaper material allows us to maximize the car's heating capabilities." Ironically, Jahn stumbled upon his diaper-based testing method in the middle of summer. During a swim with his daughter, he noticed her diaper multiplied in size when it came into contact with water.

GM Design shows what could have been and what might be

We periodically like to check in with GM Design's Instagram account to see what they're cooking up. Even better is when we catch a glimpse of an alternate history of what legendary designers from The General's past were thinking, though those ideas may not have made it into production. This week, for example, the account posted some illustrations from George Camp, whose career at GM spanned nearly four decades, from 1963 to 2001. One of the renderings is of what appears to be a 1971-72 Pontiac GTO Judge, but with two headlights instead of the production unit's quad beams. The rear departs from the canonical version most dramatically, with a massive integrated wing. Other bits that didn't make the production cut include large side vents, a gill-like side marker and rectangular intakes below the headlights that wouldn't be out of place on a modern design today. Amazingly, from what we can make out of the date, it appears that the drawing was done sometime in 1965, which makes it quite prescient.           View this post on Instagram                       A post shared by GM Design (@generalmotorsdesign) There's also a very aerodynamic interpretation of a Corvette ZR-1. To our eyes it splits the difference between the 1986 Corvette Indy concept and a fourth-generation F-body Pontiac Firebird, so perhaps parts of Camp's work on this sketch did make it into physical form. There's also a radical sports car concept from May 1970 that resembles the Mazda RX-500 concept from the same year, a Syd Mead-looking Cadillac coupe, and an Oldsmobile with a cool take on the company's trademark waterfall grille and elements of the Colonnade Cutlass at the rear. Other recent posts include a FJ Cruiser-like off-road EV, a sleek coupe with the Chevy corporate grille, and a rendering of a Silverado-esque pickup that looks far better than the current production version.           View this post on Instagram                       A post shared by GM Design (@generalmotorsdesign) It's pretty easy to lose hours in the account, but it's always fascinating to see GM's visions of what could have been and what might be. Related Video:

2013 Chevy COPO Camaro announced with two new engines and manual option

Chevrolet is following up the 2012 COPO Camaro with another limited run of the drag-strip-ready production car for 2013. Ditching the superchargers, the 2013 COPO Camaro can only be equipped with one of three naturally aspirated V8 engines, and other new features include the option of a manual transmission, new front springs, some minor styling changes and a lower starting price of $86,000. All cars are designed to abide by the rules of the NHRA's Stock Eliminator or Super Stock classifications, depending on in which series buyers wish to enter their Chevrolet Camaro.
Returning for 2013 is the 427-cubic-inch V8 producing 425 horsepower, but the new engines include a 325-hp 350-CID V8 and a 375-hp 396-CID V8. Buyers can select to purchase all three engines, and each will be matched with the sequence number of that car; the track-only COPO cars will not have vehicle identification numbers and can't be registered for street use.
Chevrolet is also offering unique enthusiast-specific options such as a COPO Build Book and the opportunity for owners to help assemble their car's engine at the Chevrolet Performance Build Center in Wixom, MI.