1962 Chevrolet Corvette on 2040-cars

Auto blog

Leaked GM document shows GMC Sierra I6 diesel is more powerful than F-150's

GM told us earlier this year that the 2019 GMC Sierra would be getting a 3.0-liter I6 diesel option, but it never mentioned power or fuel economy figures. Hold the phone though, because a leaked GM Canada document just showed up online that lists out the details we've been waiting for. Originally published by TFL Truck, the 3.0-liter oil-burner supposedly makes 282 horsepower and 450 pound-feet of torque. For those who are counting, that's more than the Ford F-150's 250 horsepower and 440 pound-feet from its 3.0-liter diesel. It soundly bests the 240 horsepower and 420 pound-feet of torque from Ram's 3.0-liter diesel as well. Fuel economy is another story, though. The promotional material states that it will get 28 mpg on the highway, which is 2 mpg short of the F-150's 30 mpg — mind you, it's only capable of that magical 30 mpg figure in rear-wheel drive form. There's another caveat here, too; these are numbers for Canada, so they're not exactly finalized EPA figures. However, we wouldn't expect drastic differences between the two when the American numbers come out. The leaked documents also state the diesel Sierra will be capable of towing 7,800 pounds. That number seems remarkably low when compared to the F-150, which can tow up to 11,400 pounds with its diesel. Extra power and torque would have us assume that GM could get even better numbers than Ford, so we're going to hold our final judgment for official word. A 10-speed automatic will do the shifting on the diesel, just like on the 6.2-liter V8. Since the Chevy Silverado is also expected to get this engine, we can assume the figures would be almost, if not identical, to those we see here. We recently drove the 2019 Sierra and Silverado without the diesel engines, so go check those reviews out if you'd like to know more of our thoughts on the redesigned GM trucks. Related video:

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

A car writer's year in new vehicles [w/video]

Christmas is only a week away. The New Year is just around the corner. As 2014 draws to a close, I'm not the only one taking stock of the year that's we're almost shut of. Depending on who you are or what you do, the end of the year can bring to mind tax bills, school semesters or scheduling dental appointments. For me, for the last eight or nine years, at least a small part of this transitory time is occupied with recalling the cars I've driven over the preceding 12 months. Since I started writing about and reviewing cars in 2006, I've done an uneven job of tracking every vehicle I've been in, each year. Last year I made a resolution to be better about it, and the result is a spreadsheet with model names, dates, notes and some basic facts and figures. Armed with this basic data and a yen for year-end stories, I figured it would be interesting to parse the figures and quantify my year in cars in a way I'd never done before. The results are, well, they're a little bizarre, honestly. And I think they'll affect how I approach this gig in 2015. {C} My tally for the year is 68 cars, as of this writing. Before the calendar flips to 2015 it'll be as high as 73. Let me give you a tiny bit of background about how automotive journalists typically get cars to test. There are basically two pools of vehicles I drive on a regular basis: media fleet vehicles and those available on "first drive" programs. The latter group is pretty self-explanatory. Journalists are gathered in one location (sometimes local, sometimes far-flung) with a new model(s), there's usually a day of driving, then we report back to you with our impressions. Media fleet vehicles are different. These are distributed to publications and individual journalists far and wide, and the test period goes from a few days to a week or more. Whereas first drives almost always result in a piece of review content, fleet loans only sometimes do. Other times they serve to give context about brands, segments, technology and the like, to editors and writers. So, adding up the loans I've had out of the press fleet and things I've driven at events, my tally for the year is 68 cars, as of this writing. Before the calendar flips to 2015, it'll be as high as 73. At one of the buff books like Car and Driver or Motor Trend, reviewers might rotate through five cars a week, or more. I know that number sounds high, but as best I can tell, it's pretty average for the full-time professionals in this business.