Canadian Built Ss Chevelle, Nicely Built 454 Big Block, 4 Speed, Fathom Green on 2040-cars

Auto blog

GM recalling 686k Lambda-platform models for hatch repair

General Motors is recalling 686,287 units of its Lambda platform crossovers. On models equipped with a power rear hatch the system can potentially fail. This campaign includes the 2008-2012 Buick Enclave, 2009-2012 Chevrolet Traverse, 2007-2012 GMC Acadia, and 2007-2010 Saturn Outlook. According to GM's documents to the National Highway Traffic Safety Administration (as a PDF), dirt can get into a portion of the strut that holds up the hatch and cause the part to prematurely fail. There's a redundancy in place called the Prop Rod Recovery system that's designed to shut the liftgate if there's a malfunction. However, if the breakdown happens too quickly after the hatch is opened the prop rod might not work the way it's supposed to. If someone were in the way of the falling liftgate, they could be hurt. For the repair, dealers will update the software for the power liftgate actuator motor control unit to prevent the hatch from closing so quickly. They'll also check the operation of the system afterward. Related Video: RECALL Subject : Liftgate Struts may Fail and Liftgate may Fall Report Receipt Date: JUN 30, 2015 NHTSA Campaign Number: 15V415000 Component(s): STRUCTURE Potential Number of Units Affected: 686,287 All Products Associated with this Recall Vehicle Make Model Model Year(s) BUICK ENCLAVE 2008-2012 CHEVROLET TRAVERSE 2009-2012 GMC ACADIA 2007-2012 SATURN OUTLOOK 2007-2010 Details Manufacturer: General Motors LLC SUMMARY: General Motors LLC (GM) is recalling certain model year 2008-2012 Buick Enclave vehicles manufactured January 3, 2007, to February 29, 2012, 2009-2012 Chevrolet Traverse vehicles manufactured July 6, 2008, to February 29, 2012, 2007-2012 GMC Acadia vehicles manufactured September 15, 2006, to February 29, 2012, and 2007-2010 Saturn Outlook vehicles manufactured August 17, 2006, to March 18, 2010. The affected vehicles, equipped with the power liftgate option, have gas struts that hold the power liftgate up when open. These struts may prematurely wear and the open liftgate may suddenly fall. CONSEQUENCE: If the open liftgate unexpectedly falls, it may strike a person, increasing their risk of injury. REMEDY: GM will notify owners, and dealers will update the software for the power liftgate actuator motor control unit so that the motor will prevent the rapid closing of the lift gate, free of charge. The manufacturer has not yet provided a notification schedule.

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM announces net 220 job increase as Trump visits Michigan

GM announced today that about 900 jobs would be added (or, importantly, retained) ahead of President Trump's arrival in Michigan, where he is expected to discuss his plan to roll back fuel economy standards. The timing of the announcement is almost certainly not coincidental, as appending it to a Trump visit gives it a higher profile and dovetails with the President's jobs agenda. It's less likely the decision itself was made for those reasons, but the free PR boost is a nice bonus. As for those 900 jobs themselves, they aren't all new jobs. The only net gain is approximately 220 jobs at the Romulus Powertrain Plant, which produces the 10-speed automatic transmission that's proliferating through the company's lineup. The 180 jobs at Flint Assembly and 500 jobs at Lansing Delta Township are retained jobs – that is to say, spots the company found for workers who would otherwise have been laid off. By the way, the Flint jobs will help with production of heavy-duty pickups, and the Lansing jobs are to produce the Chevrolet Traverse and Buick Enclave. Finding jobs for manufacturing workers in the auto sector, whether new or retained, is admirable. No matter how GM couches it, the company has created or retained a total of 7,000 jobs this year, and its total reinvestment in US production is around $1 billion. But these decisions are business ones, not political ones – timing the announcements to make them seem inspired by economic policy, or the political situation, is simply smart PR. Related Video: Image Credit: Bill Pugliano/Getty Images Celebrities Government/Legal Buick Cadillac Chevrolet GMC