1971 Chevrolet Chevelle on 2040-cars

Auto blog

Corvette Z06 and Viper TA square off at the strip

There are many long-standing grudge matches among automobiles: 911 vs GT-R, Mustang vs Camaro, Ferrari vs Lamborghini... but as far as high-end American metal goes, it doesn't get much more legendary than Viper vs 'Vette. So after Chevy released the new Corvette Z06, we knew it was only a matter of time before it would have to square off against the Viper TA. And what better place to pit these two parallel pillars of American performance than on the drag strip? Fortunately that's just what we have here. In one corner, the 2014 Dodge Viper TA, with its 8.4-liter V10 pumping out 640 horsepower and 600 pound-feet of torque. In the other, the 2015 Chevrolet Corvette Z06, the supercharger on its 6.2-liter V8 more than making up for the discrepancy in displacement and cylinder count to produce 650 hp and just as much torque. But numbers don't tell the whole story, so watch the video clip to see which reaches the end of the quarter-mile first. News Source: To the Floor via YouTubeTip: James Chevrolet Dodge Videos drag race chevy corvette z06 quarter mile drag strip srt viper ta

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

The Jitterbugs somersaulted at the 1986 Chicago Auto Show for the Chevy Nova

Judging by the vintage videos that the Chicago Auto Show has been uploading, if you wanted to check out the latest vehicles and watch some dancers in the same place in the late '80s and early '90s, then the Windy City event was definitely the place to be. We've already seen the Footlockers pitching the Cavalier in '88 and a troupe of women singing about the Geo brand in '91. Apparently, the trend went back even further, though. Just take a look at this group called the Jitterbugs selling some badge-engineered products from Chevrolet at the 1986 show. Flanked by the Chevy Nova and Spectrum, these guys managed to do a few pretty impressive jumps and somersaults but mixed them with some rather uninspired spins, as well. Also, wait for 1:24 into the clip to see the least enthusiastic backup dancers that the world has ever known. The Jitterbugs are even further proof that Chevy's habit of mixing dancing and its vehicles goes back even further than the Volt. News Source: ChicagoAutoShow via YouTube Auto News Marketing/Advertising Chicago Auto Show Chevrolet Videos Chicago chevy nova