1968 Chevelle Malibu Project Car on 2040-cars

Auto blog

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

Burt Reynolds' vehicles up for auction at Barrett-Jackson

Burt Reynolds' influence on car culture cannot be overstated. Be it "Smokey and the Bandit" or "Cannonball Run," his films inspired a generation of car enthusiasts. He died a few weeks back from cardiac arrest at age 82. This weekend, four vehicles from Reynolds' personal collection — three Pontiacs and a Chevy — will go up for auction at Barrett-Jackson in Las Vegas. It seems Reynolds had plans to sell the cars before he passed. He even filmed a short teaser for the auction and planned to attend the event himself. Three of the cars are Pontiac Trans Ams. Two are re-creations of the cars he drove in "Bandit" and the film "Hooper." Both are 1978 models. The third Trans Am is from 1984 and was used to promote Reynolds' USFL team, the Tampa Bay Bandits. The fourth vehicle is a 1978 Chevy R30 pickup truck. It's styled like the truck he drove in "Cannonball Run." None of the vehicles were actually used in the movies. But they were registered in his name, making them far more legitimate than some other movie-inspired clones. It's unclear how many Bandit Trans Ams Reynolds has owned over the years. Another car connected to him sold for $450,000 back in 2014. His death is sure to drive the price of these new cars even higher. Related Video: Image Credit: Barrett-Jackson Celebrities Chevrolet Pontiac Auctions Truck Coupe pontiac trans am burt reynolds

GM CEO to meet with U.S. lawmakers over job cuts

WASHINGTON — General Motors Co Chief Executive Mary Barra plans to visit Capitol Hill next week to discuss the company's plans to halt production at five plants in North America next year and cut up to 15,000 jobs, two congressional aides said on Friday. GM has come under harsh criticism from lawmakers from both major political parties, and from President Donald Trump, since Monday when it announced the biggest restructuring for the U.S. No. 1 carmaker since its bankruptcy a decade ago. Barra is expected to meet with lawmakers from Michigan and Ohio, where GM plans to shutter three plants, as well as senior leaders in Congress. GM did not immediately comment. Barra has been calling lawmakers this week to explain the decision to end production. Trump has threatened to revoke subsidies for GM. The Detroit automaker plans to halt production next year at three assembly plants: the Lordstown small-car factory near Youngstown, Ohio; the Detroit-Hamtramck complex in Detroit; and the Oshawa, Ontario, assembly complex near Toronto. It will also stop building several models now assembled at those plants, including the Chevrolet Cruze, the Chevrolet Volt hybrid, the Cadillac CT6 and the Buick LaCrosse. Additionally, GM plans to shutter the Warren transmission plant outside Detroit and a plant that makes electric motors and drivetrains outside Baltimore, Maryland. The Cruze compact car will be discontinued in the U.S. market in 2019, although GM may continue building it in Mexico for other markets, Barra said. Reporting by David Shepardson. Related Video: