Auto blog

2021 Chevy Colorado and GMC Canyon facelift spied

The Chevy Colorado and its GMC Canyon twin have been on sale for a good long time now, and while things move a little more slowly on the truck side when it comes to facelifts and model changeovers, it seems like it’s about time. So itÂ’s no surprise to see some lightly camouflaged trucks running around ahead of what appears to be a minor refresh for the 2021 model year. Starting with the Colorado, it appears to have a bowtie hiding behind some camo in the center of the grille, which otherwise looks like the no-bowtie option you can get on 2019-and-up trucks. It could be that Chevy is keeping the no-bowtie grille design but allowing a bowtie to grace it, or it could be misdirection. Either way, the grille pattern adds a bit of flair to the otherwise staid front end design. There also appears to be a bit more shape to the lower air inlet, with echoes of some of the lower fascias of its bigger Silverado stablemate. The Canyon, on the other hand, shows more extensive front-end changes. At first glance, it looks to emulate some variants of the GMC Sierra, which would make sense given those modelsÂ’ changes for the 2020 model year. In particular, this Canyon has hints of Sierra HD, being more square and monolithic than the regular Sierra 1500s, although itÂ’s a little hard to tell with the camo covering the edges of the grille. It could certainly also adopt more rounded corners like the 1500s. Either way, itÂ’s more vertical and thereÂ’s less differentiation between the upper grille and lower opening. ThereÂ’s nothing in the way of changes around the sides or back, and while there may be some minor changes inside, we arenÂ’t expecting any. The word around town is that this isnÂ’t a full facelift, but rather a minor front end tweak thatÂ’ll just be a regular part of the model-year changeover. 

Experimental mid-engine XP-819 Corvette going up for auction

It seems to be commonplace that when a new Corvette is in development, rumors swirl about a possible mid-engine layout. As is the case of Chevy's most recent C7 Corvette, these rumors never pan out.
In any case, the idea for a 'Vette with an engine mounted behind the driver can probably all be traced back to a single car, the 1964 XP-819 prototype. Built as an "engineering exercise" back in 1964, the prototype was designed with a rear-mounted engine. History tells us that the idea of a rear-engine Corvette fizzled, and the XP-819 was eventually cut up into pieces and stored at a shop in Daytona Beach, FL.
After sitting for untold years, a restoration project started on the car, and while it isn't yet fully completed, the current owner of the car, Mid America Motorworks, will have the car on display at the 2013 Amelia Island Concours d'Elegance as a "driveable chassis" with hopes of having a fully completed car ready to bring to next year's show.

GM won't really kill off the Chevy Volt and Cadillac CT6, will it?

General Motors is apparently considering killing off six slow-selling models by 2020, according to Reuters. But is that really likely? The news is mentioned in a story where UAW president Dennis Williams notes that slumping US car sales could threaten jobs at low-volume factories. Still, we're skeptical that GM is really serious about killing those cars. Reuters specifically calls out the Buick LaCrosse, Cadillac CT6, Cadillac XTS, Chevrolet Impala, Chevrolet Sonic, and the Chevrolet Volt. Most of these have been redesigned or refreshed within the past few model years. Four - the LaCrosse, Impala, CT6, and Volt - are built in the Hamtramck factory in Detroit. That plant has made only 35,000 cars this year - down 32 percent from 2016. A typical GM plant builds 200,000-300,000 vehicles a year. Of all the cars Williams listed, killing the XTS, Impala, and Sonic make the most sense. They're older and don't sell particularly well. On the other hand, axing the other three seems like an odd move. It would leave Buick and Cadillac without flagship sedans, at least until the rumored Cadillac CT8 arrives. The CT6 was a big investment for GM and backing out after just a few years would be a huge loss. It also uses GM's latest and best materials and technology, making us even more skeptical. The Volt is a hugely important car for Chevrolet, and supplementing it with a crossover makes more sense than replacing it with one. Offering one model with a range of powertrain variants like the Hyundai Ioniq and Toyota Prius might be another route GM could take. All six of these vehicles are sedans, Yes, crossover sales are booming, but there's still a huge market for cars. Backing away from these would be essentially giving up sales to competitors from around the globe. The UAW might simply be publicly pushing GM to move crossover production to Hamtramck to avoid closing the plant and laying off workers. Sales of passenger cars are down across both GM and the industry. Consolidating production in other plants and closing Hamtramck rather than having a single facility focus on sedans might make more sense from a business perspective. GM is also trying to reduce its unsold inventory, meaning current production may be slowed or halted while current cars move into customer hands. There's a lot of politics that goes into building a car. GM wants to do what makes the most sense from a business perspective, while the UAW doesn't workers to lose their jobs when a factory closes.