2014 Chevrolet Captiva Sport Ltz on 2040-cars

Auto blog

GM follows up Lambda CUV stop-sale with tire recall

In late January, General Motors announced a stop-sale for about 6,281 examples of the 2015 Chevrolet Traverse, GMC Acadia and Buick Enclave because of the possibility for the treads cracking on their 18-inch Goodyear Fortera HL tires. At the time, GM said that this would also eventually lead to a safety campaign to repair the problem, and the National Highway Traffic Safety Administration has just published those details. GM's recall covers 5,876 of the three Lambda platform crossovers to replace their tires. According to NHTSA, if the treads crack, there could be a loss of pressure and possible failure. Goodyear already announced its own recall of the tires after internal testing found small tread cracks. The company did not believe this was safety issue, but the problem did put the rubber out of compliance with federal laws. The business's safety campaign covered an estimated 48,512 tires. Of those, around 32,000 were reportedly made for GM to either be fitted to vehicles or sold as replacements. The remainder went to the aftermarket. Goodyear's portion of the recall is expected to begin around February 20. RECALL Subject : Tire Tread Cracking/FMVSS 110 Report Receipt Date: JAN 28, 2015 NHTSA Campaign Number: 15V044000 Component(s): TIRES Potential Number of Units Affected: 5,876 All Products Associated with this Recall Vehicle Make Model Model Year(s) BUICK ENCLAVE 2015 CHEVROLET TRAVERSE 2015 GMC ACADIA 2015 Details Manufacturer: General Motors LLC SUMMARY: General Motors LLC (GM) is recalling certain model year 2015 Buick Enclave vehicles manufactured December 9, 2014, to January 14, 2015, 2015 Chevrolet Traverse vehicles manufactured December 9, 2014, to January 20, 2015, and 2015 GMC Acadia vehicles manufactured December 9, 2014, to January 16, 2015, and all equipped with Goodyear P255/65R18 Fortera HL tires. These vehicles are equipped with tires that may experience tread cracking. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 110, "Tire Selection and Rims and Motor Home/Recreation Vehicle Trailer Load Carrying Capacity Information for Motor Vehicles with a GVWR of 4,536 kilograms (10,000 pounds) or Less." CONSEQUENCE: If the tire treads crack, a loss of tire pressure and possible tire failure may result, increasing the risk of a crash. REMEDY: GM will notify owners, and dealers will replace the tires that were manufactured within a specific date range, free of charge.

Camaro spy shots show subtly different grille, front fascia

It looks like there some changes in store for the Chevrolet Camaro - the only thing is that we just don't know what Chevy has up its sleeve. Looking at these spy shots, we'd initially be inclined to think that there is just a minor facelift or a new special edition, but upon closer inspection, there are a few oddities about this car that definitely have us intrigued.
The most obvious difference on this prototype is the slightly restyled front fascia with a smaller lower air inlet and the two-bar grille. Then we get to some of the car's mysterious details. For starters, this fascia has the SS vent above the grille, but it looks to be blocked off. Granted this could just be a one-off piece used for testing. What really piqued our interest was at the rear of the car where it has quad exhaust outlets that are used on the ZL1. Could this be the LS7-powered Camaro that we reported on back in December?
At this point, your guess is as good as ours as to what we're looking at here, so let us know in the comments what you think this could be.

Experimental mid-engine XP-819 Corvette going up for auction

It seems to be commonplace that when a new Corvette is in development, rumors swirl about a possible mid-engine layout. As is the case of Chevy's most recent C7 Corvette, these rumors never pan out.
In any case, the idea for a 'Vette with an engine mounted behind the driver can probably all be traced back to a single car, the 1964 XP-819 prototype. Built as an "engineering exercise" back in 1964, the prototype was designed with a rear-mounted engine. History tells us that the idea of a rear-engine Corvette fizzled, and the XP-819 was eventually cut up into pieces and stored at a shop in Daytona Beach, FL.
After sitting for untold years, a restoration project started on the car, and while it isn't yet fully completed, the current owner of the car, Mid America Motorworks, will have the car on display at the 2013 Amelia Island Concours d'Elegance as a "driveable chassis" with hopes of having a fully completed car ready to bring to next year's show.