1994_k3500_1ton_4x4_6.5l Turbo Diesel on 2040-cars

Auto blog

'84 MotorWeek Cherokee, Bronco and Blazer comparison indulges your SUV nostalgia

These days, truck-based, full-frame SUVs are somewhat of a rarity on the auto landscape due to the rapid rise in popularity of easier-driving, car-based crossovers. Although, without the gradually building popularity of these chunky, high-riding vehicles decades ago, it's unlikely that America's roads would be filled with so many CUVs today. In its latest dig into the archives, MotorWeek has found a 1984 comparison test of a trio of these early Sport Utility Wagons, as long-time host John Davis called them, that helped get acceptance of this segment going. This is a red, white and blue test of the SUVs from American automakers at the time and pits the Chevrolet Blazer, Ford Bronco and Jeep Cherokee (specifically in Wagoneer guise) against each other. Driving manners and interior usability are considered in the evaluation, but Motorweek actually takes these vehicles off road, too. Among the bigger revelations is the improvement in on-road ability in the past 30 years. While specific 0-60 times aren't given, all three models take around 10 seconds just to get to around 50 miles per hour in the 500-feet on-ramp acceleration test. Check out this clip to see just how far this segment has progressed in the past three decades or just get a blast of nostalgia from these now vintage models. News Source: MotorWeek via YouTube Chevrolet Ford Jeep SUV Off-Road Vehicles Classics Videos Ford Bronco chevy blazer

GM patent reveals new two-stage turbocharger

Modern turbochargers may be some of the best ever made, but performance is something that engineers are always trying to improve. According to GM Inside News, General Motors (GM) is hoping to alleviate some of the negative aspects of a two-stage turbocharger setup with a newly-patented design. The patent, that was filed on May 19, 2016, reveals a clever bypass system that allows the engine, a four-cylinder unit, to optimize both the low-pressure and high-pressure inlets for its respective functions. According to the filing, a conventional two-stage turbocharger setup is engineered to allow both turbines to operate simultaneously at low and mid engine speeds. At high engine speeds, only the low-pressure turbine works. The setup can't isolate either the low or high pressure side, which can impair low-end performance. GM's new two-stage turbocharger setup looks to eliminate this by linking the high-pressure turbo to the exhaust manifold through the high-pressure inlet duct. The low-pressure turbo is attached to the high-pressure turbo by a low-pressure inlet duct, which is linked to a connecting channel. A single actuator that is housed in the exhaust manifold creates a bypass that can opens the high-pressure inlet or close the connecting channel. Depending on what the engine load and speed is, the ECU guides the actuator—a single rotating spindle with discs corresponding to flanges on the high and low pressure sides—to isolate one of the two turbos. Isolating the turbos allow the respective inlets to be engineered for the best possible fluid dynamic performance. The setup should increase performance and decrease lag. There's no word on what car this setup will make an appearance on, but it will most likely be used in premium vehicles before trickling down to the rest of GM's vehicles. Related Video: News Source: GM Inside News, AutoGuide via GM Authority Cadillac Chevrolet GM Technology Sedan turbo patent engine turbocharging

GM to build outgoing Silverado and Sierra until late 2019

As it has done with previous generations, General Motors is keeping the outgoing versions of its 1500 pickups in production despite the arrival of the all-new 2019 Chevrolet Silverado and 2019 GMC Sierra. The production of the previous, K2 generation models will begin to be wound down gradually, according to Automotive News, starting with crew cabs "early next year," and double and regular cab models following during "the early second half of next year." The old model trucks will continue to be built into "late 2019" based on market demand, GM's spokesperson Kim Carpenter said. The Chevrolet will go by the name Silverado LD, with the GMC Sierra designation still to be announced. Some of the outgoing models are built by sharing the assembly work between two GM plants. Partially finished Silverado and Sierra double cab bodies are shipped from Fort Wayne, Ind., to Oshawa, Ont., where the trucks are completed, including receiving paint. This eases the workload in Fort Wayne, where production of the new T1 generation trucks started in July 2018. In January, the Silao plant in Mexico will take on the duties of building new generation regular cab and crew cab trucks. Carpenter also said that the "Oshawa shuttle," as the shared production is called, has been very successful. As a result, 60,000 more trucks will be built than what the original production forecast initially called for. GM's latest quarterly profits, disclosed last week to be $1 billion, have been far higher than expected and will result in full-year profits far higher than what had been predicted in light of steel tariffs. GM isn't the only truck maker taking a similar multi-generation approach for 2019. Both the outgoing and redesigned Ram 1500 are in production, with the previous generation being dubbed Ram 1500 Classic. Related Video: