on 2040-cars

Auto blog

Recharge Wrap-up: Chevy Volt's new, improved powertrain; Inabikari wants to build Tesla Model X fighter

We knew the 2016 Chevrolet Volt's new powertrain would provide more range, but we didn't know how much. According to GM's Executive Director Larry Nitz, it is about 12 percent more, overall. "I can't think of a powertrain we've re-engineered more extensively within a five-year period than this one," he said. The battery, electric drive system and gasoline generator have all been reworked to allow for an overall driving range of up to 425 miles, with electric range speculated to reach 42 miles or more. The new Volt will also benefit from 20 percent quicker low-end acceleration, weight reductions and improvements in NVH. Read more at Hybrid Cars and at the SAE website. Hyundai's FCEV research and development boss, Dr. Sae-Hoon Kim, is optimistic about the future of hydrogen mobility in Japan. With the Tucson Fuel Cell already in production ahead of Toyota's FCV, Hyundai has a foothold in the hydrogen car scene. Kim believes that since the Fukushima disaster, Japan's attitudes toward energy make it friendly to a growing hydrogen economy. He also says that hydrogen won't be limited to Hyundai, with Kia getting all the battery EVs. "Both types are for both companies," Kim says. "For the moment, volumes are small and it is not wise to have Hyundai and Kia competing." Read more at Just Auto. The Latvian/German startup Inabikari is using crowdfunding to build an electric crossover for Europe. The Rev.01 EV hopes to compete with Tesla's upcoming Model X with a range of over 400 miles and a five-second 0-60 time. The group currently is trying to raise initial funds through an Indiegogo campaign, with hopes of more investment in the future and sales beginning in 2017. See the video below, and read more at Hybrid Cars and at the Inabikari website. Fuel economy and emissions regulations could lead to some interesting design changes to automobiles. The World Light Duty Test Procedure, set to replace the New European Driving Cycle in 2017, will push automakers to find new ways to reduce drag on their vehicles. For better aerodynamics, we could see traditional side-view mirrors replaced by cameras that display what they see on screens inside the vehicle. Another likely change will be the introduction of smaller, narrower wheels. Improving the average drag coefficient from 0.32 to 0.20 could reduce CO2 emissions by as much as 20 percent. Read more at Automotive News Europe.

Amelia Island 2013: Chevrolet Corvette Sting Ray from concepts to split windows

While this year marks 60 years of the Chevrolet Corvette, the 2013 Amelia Island Concours d'Elegance focused on one of the coupe's most sought after models, the 1963 Sting Ray. General Motors design boss Ed Welburn was on hand to show off the all-new C7 Corvette, but even the hard-edged styling of the 2014 Stingray couldn't take away from the beautiful 1963 models sitting out on the field.
In addition to the original Sting Ray and the 1959 Sting Ray Concept, some of the other classic 'Vettes included "Big Tank" racecars, an interesting cutaway coupe, a right-hand-drive Z06 and the attention-grabbing 1963 Corvette Rondine by Pininfarina. Another impressive Corvette was the 1964 Corvette XP-819 rear-engine prototype. Owner Mike Yager had the car finished as a driving chassis for this year's show, but promises the car will be back to its original glory in time for next year's event.

Surprise! GM putting aluminum in next-gen pickups

Last month, General Motors launched a series of ads touting the benefits of steel over aluminum – specifically, with regard to the Chevy Silverado versus the Ford F-150. (Kind of. We're not sure what a grizzly bear has to do with anything.) We took issue with the ads, with editor in chief Mike Austin saying they "reek of insecurity, and distract from the Silverado's strengths that could be used for positive advertising." But what bothers us more, is that yet another report surfaced claiming anti-aluminum GM will indeed use the weight-saving material in its next-generation fullsize trucks. On Tuesday, GM announced a $877-million investment for its truck plant in Flint, MI. But Reuters says that huge overhaul is because the trucks will use "substantially different equipment than the tools GM uses today." The report specifically states, "People familiar with the company's plans say GM's next-generation pickups and SUVs will make use of various materials, including aluminum and lightweight steel, to shed weight and gain fuel efficiency to meet tougher federal standards." The Silverado already uses a few aluminum components in the engine and hood, and if more widespread use will help GM build its best fullsize trucks ever, then that's great. Honestly, we have no reason to doubt that aluminum will be used in the next Silverado and GMC Sierra. We just hope GM remembers that nothing is ever truly deleted from the bowels of the Internet when it launches the subsequent "look how great aluminum is!" campaign. Related Video: News Source: Reuters Green Plants/Manufacturing Chevrolet GM GMC Truck aluminum steel