1966 Chevy Truck on 2040-cars

Auto blog

2020 Chevy Trax and Buick Encore spied testing

We just recently saw a little crossover SUV from General Motors being tested, and we weren't positive what brand it belonged to. We narrowed it down to Chevy or GMC, but we're feeling more confident that it's a GMC now, since both the next generation Chevy Trax and Buick Encore subcompact crossover SUVs have been spied testing together. Of the two, the Chevy has the more radically different sheet metal. It ditches the somewhat frumpy, lumpy shape of the current Trax for a body inspired by the bigger Chevy Blazer. The roofline has sharp corners, and the hood is wide and flat. The front fascia, though obscured, shows the most connection to the bigger crossover. It has the same split headlight configuration, and it looks as though the grille takes up a sizable section of the fascia. View 7 Photos The Buick Encore on the other hand looks evolutionary in design. The body still has plenty of curves, and the distinctive, sharply rising window sill are all hallmarks of the current Encore design. The headlights and grille are similar, too, though the grille appears to be slightly updated to fit in with the Enclave and Regal. It's understandable that Buick might want to play it safe with the new Encore, since the model is Buick's best seller, selling about 23,000 units in the last quarter, nearly twice that of the next best performer, the Enclave. Since this is the first time we've seen these little crossovers, we expect it will still be a year or two before we get to see them fully revealed. They will probably continue to use small-displacement turbocharged four-cylinder engines with either front- or all-wheel drive. Related Video:

Why does the Corvette Stingray have so many vents? Here's why

Just looking at the new 2014 Chevrolet Corvette Stingray, it's not hard to see that the car's design was created with aerodynamics at the forefront, but Chevrolet designers point out exactly what went into designing the iconic coupe in a pair of recently released videos. The videos show the Corvette going through early design phases, including clay models and wind tunnel tests, as well as talking to the car's chief engineer, Tadge Juechter.
Both videos help explain various aspects of the C7 Corvette, but it's the aero tuning of the car that is most interesting. This includes extra attention paid to the lower air dam and vented hood to help reduce drag and lift, while the rear quarter inlets are for differential and transmission cooling. Juechter said that some of these aero-tuned elements were inspired from GM's involvement in racing.
If you have about five minutes and you can't get enough information about the new 'Vette, then check out the videos posted below.

GM patent reveals new two-stage turbocharger

Modern turbochargers may be some of the best ever made, but performance is something that engineers are always trying to improve. According to GM Inside News, General Motors (GM) is hoping to alleviate some of the negative aspects of a two-stage turbocharger setup with a newly-patented design. The patent, that was filed on May 19, 2016, reveals a clever bypass system that allows the engine, a four-cylinder unit, to optimize both the low-pressure and high-pressure inlets for its respective functions. According to the filing, a conventional two-stage turbocharger setup is engineered to allow both turbines to operate simultaneously at low and mid engine speeds. At high engine speeds, only the low-pressure turbine works. The setup can't isolate either the low or high pressure side, which can impair low-end performance. GM's new two-stage turbocharger setup looks to eliminate this by linking the high-pressure turbo to the exhaust manifold through the high-pressure inlet duct. The low-pressure turbo is attached to the high-pressure turbo by a low-pressure inlet duct, which is linked to a connecting channel. A single actuator that is housed in the exhaust manifold creates a bypass that can opens the high-pressure inlet or close the connecting channel. Depending on what the engine load and speed is, the ECU guides the actuator—a single rotating spindle with discs corresponding to flanges on the high and low pressure sides—to isolate one of the two turbos. Isolating the turbos allow the respective inlets to be engineered for the best possible fluid dynamic performance. The setup should increase performance and decrease lag. There's no word on what car this setup will make an appearance on, but it will most likely be used in premium vehicles before trickling down to the rest of GM's vehicles. Related Video: News Source: GM Inside News, AutoGuide via GM Authority Cadillac Chevrolet GM Technology Sedan turbo patent engine turbocharging