1964 Chevy C10 Shop Truck on 2040-cars

Auto blog

Chevy's 6.6-liter Duramax is pretty much all new

To say there's a heated battle in heavy-duty pickups is an understatement, with Chevrolet, Ford, and Ram constantly trading blows of increased torque, horsepower, and towing capacity. The latest salvo is the revised, more powerful turbo diesel 6.6-liter Duramax V8 in the 2017 Chevy Silverado. It has 910 pound-feet of torque, an increase of 145, putting it nearly level with the Ford Super Duty. Here's a closer look at where those gains come from. How exactly did Chevrolet add all that torque plus 48 horsepower? The automaker essentially took a fine-tooth comb to the entire engine. Chevy says it changed 90 percent of the V8, and the cumulative effect of those small changes adds up to big increases. As you might guess, the turbocharger is updated. The larger unit features electric actuation of the variable nozzle turbine (VNT), and what Chevy calls a double axle cartridge mechanism that separates the VNT moving parts from the housing. That helps with heat performance as well, with a claim that the exhaust side of the turbo can run continuously up to 1,436 degrees Fahrenheit. Helping that cause are six exhaust gaskets made of Inconel - an nickel alloy that contains chromium and iron – and upgraded stainless steel for the exhaust manifold. Despite having the same cast iron cylinder block, albeit with some minor enhancements, the engine has new cylinder heads, pistons, piston pins, connecting rods, and crankshaft, which have all been upgraded to handle 20 percent higher cylinder pressures. Alongside the increase in pressure, Chevrolet also increased the cylinder head's structure with a honeycomb design. The pattern features high-strength aluminum with dual layer water jackets that not only improve strength, but also optimize water flow for better cooling. For 2017, the cylinder head also benefits from integrated plenum that aids the engine in getting more air under heavy loads. The cylinder head isn't the only component to get a minor update, as the pistons have a larger diameter pin for improved oil flow. The same detailed improvements has been bestowed to the humble connecting rods (second in our hearts only to the inanimate carbon rod). The new design has the bolts oriented roughly 45-degrees to the rod instead of parallel. The angle split design, as it's called allows for easier passage through the cylinder.

Did the Chevy Corvette Z06 break 7 minutes at the Ring? Not likely

"Just because it's on the internet doesn't make it true." That's rule number one, two and arguably, three, of surfing the world wide web. In today's example of this rule, we have the following. The website HorsepowerKings is claiming that a 2015 Chevrolet Corvette Z06, with the eight-speed automatic and Z07 package, managed to lap the Nurburgring Nordschleife in under seven minutes. To put that in perspective, that super-quick time would put the 650-horsepower, $97,000 (the price of a 2LZ with the Z07/8AT combo) Z06 a mere two seconds slower around the world's most challenging race track than the $929,000, 887-horsepower Porsche 918 Spyder Weissach. It's about eight seconds quicker than Nissan's own test of the GT-R Nismo Track Pack and 13 seconds faster than a Dodge Viper ACR. Unfortunately, Chevy says there isn't anything to it. We reached out to the Bowtie's Monte Doran, who confirmed that HK's claims are "not accurate." "Any one – a manufacturer, a journalist, a guy standing on the fence of the Ring – can claim a lap time. As such, we think the in-car video is essential to proving a time is real and credible, and Chevrolet will not release a lap until we have a video to substantiate the claim," Doran told Autoblog. "Chevrolet accumulated nearly 1,000 miles of testing on the Nurburgring with the Z06. During that time, we only had two opportunities to run a lap on video – and both were rained out. If we get a lap on video, we will post an official time." Doran finished by referencing the "only official lap time" for the Z06 – a 2:41 around the Virginia International Raceway. Frankly, we aren't terribly surprised by Chevy's position. One would imagine if the Z06 were matching million-dollar hypercars around the 'Ring, the company would literally be screaming about it from Renaissance Center's rooftop. As this is quite the opposite of that, though, we're betting that the real Z06 lap time - while still likely very, very fast – won't be quite quick enough to frighten the brightest and best of today's hypercars.

GM veteran Bryan Nesbitt tapped to head Buick design

General Motors styling veteran Bryan Nesbitt (pictured above) took over a new role on Monday as executive director of global Buick design and global architectures. Andrew Smith, who previously did that job and also coordinated the look for Cadillac, has remained in charge of the pen at Caddy with this shift. Nesbitt rose to prominence when he designed the Chrysler PT Cruiser, according to Automotive News. He joined GM in 2001 and has been there ever since in multiple high-level roles. In 2007, he was appointed vice president of design for North America and was later briefly general manager of Cadillac in 2009-2010. Nesbitt took over as the vice president of GM's international operations design in China in 2011. This shuffle also moves Ken Parkinson, currently styling boss for Chevrolet trucks, to China as design vice president there. In addition, John Cafaro becomes the person in charge of the look for Chevy globally, rather than previously splitting that role between cars and trucks with Parkinson. GM Global Design Leadership Changes – effective June 1, 2015. Bryan Nesbitt, Design Vice President, GM China will repatriate to North America and assume the position of Executive Director, Global Buick and Global Architectures. He will be located in Warren, MI. Bryan will be the design Champion for Buick in the US and China. Ken Parkinson, Executive Director, Global Chevrolet Trucks and Global Architecture will assume the position of Design Vice President, GM China. He will be based in Shanghai, China. Andrew Smith, Executive Director, Global Cadillac and Buick Design will assume the position of Executive Director, Global Cadillac. He will continue to be the design Champion for the Cadillac brand. In addition, he will continue to lead the Global Color & Trim team. He will be based in Warren, Michigan. John Cafaro, Executive Director, Global Chevrolet Cars will assume the position of Executive Director, Global Chevrolet. He will be the design Champion for Chevrolet. In addition, John will lead the exterior components and accessories team. He will continue to be based in Warren, MI. The roles and responsibilities of Helen Emsley, Mark Adams, Carlos Barba, Clay Dean, Michael Simcoe, and Teckla Rhoades remain the same. Related Video: The video meant to be presented here is no longer available. Sorry for the inconvenience.