1963 Chevrolet C-10 on 2040-cars

Auto blog

Driving Granatelli's turbine-powered 1978 Chevy Corvette [w/video]

With its curvy snout and feminine haunches, the third-gen Chevrolet Corvette looks like a dreamy – if dated – exemplar of Sports Car Fantasy 101 when viewed through modern eyes. This particular specimen circa '78, clad in silver and black paint with red pinstripes, appears to be a well-preserved example from the era. Apart from its low-profile Pirellis, slightly raised and slotted hood, spacious stance and a certain hand-painted descriptor alongside its crossed flag logos, you'd never guess there's a Space-Age propulsion unit powering this Coke bottle-bodied ride. Climb inside, and you're presented with aircraft gauges and big, colorful square buttons in the center panel. It takes a push of the "Ignitor" button, a tap of the starter button, and a slide of a T-handle for this nearly 40-year-old sports car to start sounding like Gulfstream G650 ready for takeoff. Yep, you're sitting in an 880-horsepower, turbine-powered Corvette, the only one of its kind in the world. Welcome to the whoosh. What The...? Built by Vince Granatelli, son of Indy 500 guru Andy Granatelli, this curious Corvette came into being by cramming a Pratt & Whitney ST6N-74 gas turbine engine into the donor car's lengthy front end. The same type of Jet A-burning mill powered Granatelli Senior's STP-sponsored racecar at the 1967 Indianapolis 500, where it famously led most of the 198 of 200 laps until a $6 transmission bearing failed, knocking it out of the race. The idea of turbine power usurping internal combustion was so threatening that Indy's governing body restricted turbine performance into obsolescence thereafter. A turbine-powered Corvette sounds excessive because it is. But there are also things about this 880-horsepower, 1,161-pound-feet monster that might surprise you. While it smacks of futurist exoticism and cost a then-dizzying $37,000 in 1967, the Canadian-built powerplant uses 80 percent fewer parts than an internal combustion V8 and will run on virtually anything combustible – whiskey, diesel, even Chanel No. 5. Though it's triple the length of a V8, the Pratt & Whitney beast weighs only 285 pounds. It's also one hell of a robust workhorse, typically serving as an auxiliary power unit for commercial aircraft or a generator in oil fields, where it can run for tens of thousands of consecutive hours before needing an overhaul. To adapt the Chevrolet for jet duty, the nose section was gutted and a sub-frame was built to compensate for the loosey-goosey front end.

Junkyard Gem: 2003 Chevrolet Tracker

When General Motors created the Geo brand to sell vehicles designed and — in some cases — built by Japanese partners, the first four models were introduced for the 1989 model year: the Metro (Suzuki Cultus), Prizm (Toyota Sprinter), Spectrum (Isuzu Gemini) and Tracker (Suzuki Sidekick). Geo got the axe in 1997, with the Metro, Prizm and Tracker becoming Chevrolets. Of those, the Tracker survived the longest, with U.S.-market sales continuing into 2004. Here's an example of a very late Tracker, found in a North Carolina car graveyard recently. The 1989-1997 first-generation Trackers were based on the Suzuki Sidekick, while the 1998-2004 Trackers had the Suzuki Vitaras (not to be confused with the much grander Grand Vitaras) as their siblings. Production of these trucks for the South American market (as the Chevrolet Vitara) continued in Ecuador all the way through 2014. The Tracker name has also gone onto some versions of the Chevrolet Trax around the world. This one is a base four-door hard top/rear-wheel-drive model, which had an MSRP of $17,330. That's about $29,789 in 2024 dollars. You'll find one in every car. You'll see. The engine is a Suzuki 2.0-liter straight-four rated at 127 horsepower and 134 pound-feet. A five-speed manual was base equipment, but very few American vehicle shoppers wanted three pedals by the middle 2000s. This truck has the Aisin four-speed automatic. We like it loud. It appears that someone associated with this truck graduated from Julius L. Chambers High School last year. In the United States, the Tracker was replaced by the Saturn Vue. If Tracker can handle (unspecified Middle Eastern country), it can survive the jungle back home. Siempre contigo.

Chevrolet considering midsize crossover to slot between Traverse and Equinox

Crossovers are the new hotness, and automakers are looking to cash in by offering a size and shape for every customer. With Chevrolet's debut of the new 2018 Traverse in Detroit, which grew ever so slightly compared to the first-generation model, there is now a midsize-crossover-sized hole between the three-row Traverse and the compact Equinox. When asked about that obvious space, a Chevrolet spokesperson told us the company is looking into the possibility of expanding its crossover lineup. It should be a relatively simple thing to do, since all it would take is reskinning and rechristening the GMC Acadia with a bow tie, and we all know how much GM loves platform sharing. Although they're now different sizes, the new Acadia and Traverse still use the same platform; the Acadia is now on a short-wheelbase version of the C1XX while the Traverse uses long-wheelbase C1XX parts. A short-wheelbase Chevy built on the C1XX likely would be differentiated visually from both the Acadia and the larger Traverse. It may seem like flooding the lineup with more and more models would cannibalize sales of existing ones, but Chevrolet said it would rather have customers stay within the brand rather than going to another automaker. There have been whispers that some form of the Blazer name (possibly TrailBlazer) may make a return on a midsizer, but if it does don't expect an old-school body-on-frame SUV like the old one. In the end, if Chevy builds it, customers will come. Related Video: