60+pics Clean Carfax Certified One Owner Trade In on 2040-cars

Auto blog

Next-gen Chevy Silverado and GMC Sierra may use carbon fiber

It's been generally accepted that the next generation of full-size GM trucks will use some sort of strong, lightweight material for the beds while retaining steel for the cab. While aluminum seems like the most obvious choice, according to Automotive News, the Chevy Silverado and GMC Sierra will incorporate both aluminum and carbon fiber in their beds. The publication cites sources from within GM, though it seems the introduction of this comparatively exotic material mix is still a few years off. While carbon fiber is both stronger and lighter than steel and aluminum, it takes significantly more time and money to produce, essentially relegating the material to small-volume cars. The main benefit for trucks is the resulting reduction in weight to improve fuel economy without sacrificing the tough, rugged capabilities truck buyers expect. The Ford F-150 made the switch to aluminum for the 2015 model year and it's proved highly successful. It seemed like it was only a matter of time before the competition followed suit. Automotive News says that the next-gen trucks will launch with aluminum beds and that it will take a couple of years before we'll see any carbon fiber incorporated into the design. Even then, only look for the composite material on higher-trim models, with a trickle down to lower-spec trucks possible further in the future. In 2011, GM announced it was working with Japan-based Teijin Limited on a carbon fiber reinforced thermoplastic. There's a good chance that material's introduction will be on trucks. Related Video: News Source: Automotive News Plants/Manufacturing Rumormill Chevrolet GM GMC Truck

GM plans to restart production in Mexico on May 20

MEXICO CITY — General Motors is tentatively planning to restart operations at its auto assembly plant in the Mexican city of Silao on May 20, according to a message to workers seen by Reuters on Sunday, as the car industry prepares to exit the coronavirus lockdown. Separately, the president of GM's Mexican unit advised suppliers to prepare to resume operations. “We are now beginning a new phase given the Mexican governmentÂ’s official announcement earlier this week to consider the transportation manufacturing industry as essential for the countryÂ’s economy,” Francisco Garza, president ofGeneral Motors de Mexico, wrote in an email to suppliers dated on Friday that was viewed by Reuters. The reopening of the plant  in Silao would be a positive signal for the auto sector in North America, whose supply lines are highly interconnected between the United States, Mexico and Canada. The plant in the central state of Guanajuato has been idled for weeks due to the coronavirus outbreak. Workers had previously been told to plan to return to their jobs on May 18. A GM spokeswoman said the company could not confirm when it would restart operations at any of its facilities in Mexico because it is awaiting more guidance from the government. The message to the plant's workers came after the government on Friday clarified when the industry could begin easing restrictions imposed because of the health emergency. On Wednesday, the government said automakers could start going back into production from May 18. It then withdrew that advice and suggested the new start date would be June 1. Finally it indicated the sector, which forms the backbone of Mexican manufacturing, could begin operating as soon as next week if companies had the required safety measures in place. U.S. officials and its auto industry have pressed Mexico's government to get its factories open again because American operations depend heavily on parts from south of the border. However, some politicians are wary of opening too fast. Mexico registered its first case of coronavirus weeks after the United States and Canada and the toll of daily infections and deaths in the country reached new peaks over the past few days. The Silao production facility, which makes highly profitable pickup trucks for GM, is one of the biggest automotive plants in Guanajuato, a major Mexican carmaking state. Related Video:

GM sees 'strong year' in 2018, then gold in Chevy Silverado for 2019

DETROIT — General Motors said on Tuesday it expects earnings in 2018 to be largely flat compared with 2017, but that profits should pick up pace in 2019 as its revamped line of high-margin pickup trucks hits the U.S. market. The 2018 earnings outlook was above market expectations, sending GM shares up more than 3 percent in premarket trading. "GM had a very good 2017 as we continued to transform our company to be more focused, resilient and profitable," GM Chief Executive Mary Barra said in a statement. "We are positioned for another strong year in 2018 and an even better one in 2019." GM and its Detroit rivals, Ford and Fiat Chrysler Automobiles, are bringing on new trucks at a time when overall U.S. new vehicle sales have been falling, but truck sales continue to grow as consumers abandon passenger cars in favor of pickups, SUVs and crossovers. GM on Saturday fired a new round in the battle for profits from one of the U.S. auto industry's most lucrative segments when it showed a new generation of its Chevrolet Silverado pickup truck at the Detroit auto show. The new Silverado, a highlight of the event, is the successor to GM's best-selling vehicle in North America. Sales of the current Silverado rose nearly 2 percent to 585,000 vehicles in 2017. In the coming months, the company will also reveal a revamped GMC Sierra pickup truck. U.S. new vehicle sales fell 2 percent in 2017 after hitting a record high in 2016, and are expected to drop further in 2018 as interest rates rise and more late-model used cars return to dealer lots to compete with new ones. GM said on Tuesday that while it retools a factory in Ft. Wayne, Indiana, to make the new pickup trucks, it will shift some production to an Oshawa, Ontario, plant in order to avoid missing sales in a hot market for the vehicles. The No. 1 U.S. automaker said it will record a $7 billion non-cash charge for its fourth-quarter 2017 earnings related to deferred tax assets. GM said it expects capital expenditure in 2018 of around $8.5 billion, about $1 billion of which will go toward funding self-driving car technology. Last week, the company said it is seeking U.S. government approval for a fully autonomous car — one without a steering wheel, brake pedal or accelerator pedal — to enter the automaker's first commercial ride-sharing fleet in 2019. GM said it expects 2017 earnings per share at the high end of its previously forecast range of $6 to $6.50.